M drivers/led/aw20216s.c => drivers/led/aw20216s.c +12 -35
@@ 19,39 19,16 @@
#include "wait.h"
#include "spi_master.h"
-/* The AW20216S appears to be somewhat similar to the IS31FL743, although quite
- * a few things are different, such as the command byte format and page ordering.
- * The LED addresses start from 0x00 instead of 0x01.
- */
-#define AW20216S_ID 0b1010 << 4
-
-#define AW20216S_PAGE_FUNCTION 0x00 << 1 // PG0, Function registers
-#define AW20216S_PAGE_PWM 0x01 << 1 // PG1, LED PWM control
-#define AW20216S_PAGE_SCALING 0x02 << 1 // PG2, LED current scaling control
-#define AW20216S_PAGE_PATCHOICE 0x03 << 1 // PG3, Pattern choice?
-#define AW20216S_PAGE_PWMSCALING 0x04 << 1 // PG4, LED PWM + Scaling control?
-
-#define AW20216S_WRITE 0
-#define AW20216S_READ 1
-
-#define AW20216S_REG_CONFIGURATION 0x00 // PG0
-#define AW20216S_REG_GLOBALCURRENT 0x01 // PG0
-#define AW20216S_REG_RESET 0x2F // PG0
-#define AW20216S_REG_MIXFUNCTION 0x46 // PG0
-
-// Default value of AW20216S_REG_CONFIGURATION
-// D7:D4 = 1011, SWSEL (SW1~SW12 active)
-// D3 = 0?, reserved (apparently this should be 1 but it doesn't seem to matter)
-// D2:D1 = 00, OSDE (open/short detection enable)
-// D0 = 0, CHIPEN (write 1 to enable LEDs when hardware enable pulled high)
-#define AW20216S_CONFIG_DEFAULT 0b10110000
-#define AW20216S_MIXCR_DEFAULT 0b00000000
-#define AW20216S_RESET_CMD 0xAE
-#define AW20216S_CHIPEN 1
-#define AW20216S_LPEN (0x01 << 1)
-
#define AW20216S_PWM_REGISTER_COUNT 216
+#ifndef AW20216S_CONFIGURATION
+# define AW20216S_CONFIGURATION (AW20216S_CONFIGURATION_SWSEL_1_12 | AW20216S_CONFIGURATION_CHIPEN)
+#endif
+
+#ifndef AW20216S_MIX_FUNCTION
+# define AW20216S_MIX_FUNCTION (AW20216S_MIX_FUNCTION_LPEN)
+#endif
+
#ifndef AW20216S_SCALING_MAX
# define AW20216S_SCALING_MAX 150
#endif
@@ 102,7 79,7 @@ static inline bool aw20216s_write_register(pin_t cs_pin, uint8_t page, uint8_t r
}
void aw20216s_soft_reset(pin_t cs_pin) {
- aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_REG_RESET, AW20216S_RESET_CMD);
+ aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_FUNCTION_REG_RESET, AW20216S_RESET_MAGIC);
}
static void aw20216s_init_scaling(pin_t cs_pin) {
@@ 114,16 91,16 @@ static void aw20216s_init_scaling(pin_t cs_pin) {
static inline void aw20216s_init_current_limit(pin_t cs_pin) {
// Push config
- aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_REG_GLOBALCURRENT, AW20216S_GLOBAL_CURRENT_MAX);
+ aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_FUNCTION_REG_GLOBAL_CURRENT, AW20216S_GLOBAL_CURRENT_MAX);
}
static inline void aw20216s_soft_enable(pin_t cs_pin) {
// Push config
- aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_REG_CONFIGURATION, AW20216S_CONFIG_DEFAULT | AW20216S_CHIPEN);
+ aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_FUNCTION_REG_CONFIGURATION, AW20216S_CONFIGURATION);
}
static inline void aw20216s_auto_lowpower(pin_t cs_pin) {
- aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_REG_MIXFUNCTION, AW20216S_MIXCR_DEFAULT | AW20216S_LPEN);
+ aw20216s_write_register(cs_pin, AW20216S_PAGE_FUNCTION, AW20216S_FUNCTION_REG_MIX_FUNCTION, AW20216S_MIX_FUNCTION);
}
void aw20216s_init_drivers(void) {
M drivers/led/aw20216s.h => drivers/led/aw20216s.h +22 -0
@@ 52,6 52,28 @@
#define g_aw_leds g_aw20216s_leds
// ========
+#define AW20216S_ID (0b1010 << 4)
+#define AW20216S_WRITE 0
+#define AW20216S_READ 1
+
+#define AW20216S_PAGE_FUNCTION (0x00 << 1)
+#define AW20216S_PAGE_PWM (0x01 << 1)
+#define AW20216S_PAGE_SCALING (0x02 << 1)
+#define AW20216S_PAGE_PATTERN_CHOICE (0x03 << 1)
+#define AW20216S_PAGE_PWM_SCALING (0x04 << 1)
+
+#define AW20216S_FUNCTION_REG_CONFIGURATION 0x00
+#define AW20216S_CONFIGURATION_SWSEL_1_12 (0b1011 << 4)
+#define AW20216S_CONFIGURATION_CHIPEN (0b1 << 0)
+
+#define AW20216S_FUNCTION_REG_GLOBAL_CURRENT 0x01
+
+#define AW20216S_FUNCTION_REG_RESET 0x2F
+#define AW20216S_RESET_MAGIC 0xAE
+
+#define AW20216S_FUNCTION_REG_MIX_FUNCTION 0x46
+#define AW20216S_MIX_FUNCTION_LPEN (0b1 << 1)
+
#if defined(RGB_MATRIX_AW20216S)
# define AW20216S_LED_COUNT RGB_MATRIX_LED_COUNT
#endif
M drivers/led/issi/is31fl3218-simple.c => drivers/led/issi/is31fl3218-simple.c +2 -9
@@ 17,13 17,6 @@
#include <string.h>
#include "i2c_master.h"
-// These are the register addresses
-#define IS31FL3218_REG_SHUTDOWN 0x00
-#define IS31FL3218_REG_PWM 0x01
-#define IS31FL3218_REG_CONTROL 0x13
-#define IS31FL3218_REG_UPDATE 0x16
-#define IS31FL3218_REG_RESET 0x17
-
#define IS31FL3218_PWM_REGISTER_COUNT 18
#define IS31FL3218_LED_CONTROL_REGISTER_COUNT 3
@@ 86,7 79,7 @@ void is31fl3218_init(void) {
// turn off all LEDs in the LED control register
for (uint8_t i = 0; i < IS31FL3218_LED_CONTROL_REGISTER_COUNT; i++) {
- is31fl3218_write_register(IS31FL3218_REG_CONTROL + i, 0x00);
+ is31fl3218_write_register(IS31FL3218_REG_LED_CONTROL_1 + i, 0x00);
}
// Load PWM registers and LED Control register data
@@ 146,7 139,7 @@ void is31fl3218_update_pwm_buffers(void) {
void is31fl3218_update_led_control_registers(void) {
if (g_led_control_registers_update_required) {
for (int i = 0; i < IS31FL3218_LED_CONTROL_REGISTER_COUNT; i++) {
- is31fl3218_write_register(IS31FL3218_REG_CONTROL + i, g_led_control_registers[i]);
+ is31fl3218_write_register(IS31FL3218_REG_LED_CONTROL_1 + i, g_led_control_registers[i]);
}
g_led_control_registers_update_required = false;
M drivers/led/issi/is31fl3218-simple.h => drivers/led/issi/is31fl3218-simple.h +8 -0
@@ 21,6 21,14 @@
#include "progmem.h"
#include "util.h"
+#define IS31FL3218_REG_SHUTDOWN 0x00
+#define IS31FL3218_REG_PWM 0x01
+#define IS31FL3218_REG_LED_CONTROL_1 0x13
+#define IS31FL3218_REG_LED_CONTROL_2 0x14
+#define IS31FL3218_REG_LED_CONTROL_3 0x15
+#define IS31FL3218_REG_UPDATE 0x16
+#define IS31FL3218_REG_RESET 0x17
+
#define IS31FL3218_I2C_ADDRESS 0x54
#if defined(LED_MATRIX_IS31FL3218)
M drivers/led/issi/is31fl3218.c => drivers/led/issi/is31fl3218.c +2 -9
@@ 17,13 17,6 @@
#include <string.h>
#include "i2c_master.h"
-// These are the register addresses
-#define IS31FL3218_REG_SHUTDOWN 0x00
-#define IS31FL3218_REG_PWM 0x01
-#define IS31FL3218_REG_CONTROL 0x13
-#define IS31FL3218_REG_UPDATE 0x16
-#define IS31FL3218_REG_RESET 0x17
-
#define IS31FL3218_PWM_REGISTER_COUNT 18
#define IS31FL3218_LED_CONTROL_REGISTER_COUNT 3
@@ 86,7 79,7 @@ void is31fl3218_init(void) {
// turn off all LEDs in the LED control register
for (uint8_t i = 0; i < IS31FL3218_LED_CONTROL_REGISTER_COUNT; i++) {
- is31fl3218_write_register(IS31FL3218_REG_CONTROL + i, 0x00);
+ is31fl3218_write_register(IS31FL3218_REG_LED_CONTROL_1 + i, 0x00);
}
// Load PWM registers and LED Control register data
@@ 162,7 155,7 @@ void is31fl3218_update_pwm_buffers(void) {
void is31fl3218_update_led_control_registers(void) {
if (g_led_control_registers_update_required) {
for (int i = 0; i < IS31FL3218_LED_CONTROL_REGISTER_COUNT; i++) {
- is31fl3218_write_register(IS31FL3218_REG_CONTROL + i, g_led_control_registers[i]);
+ is31fl3218_write_register(IS31FL3218_REG_LED_CONTROL_1 + i, g_led_control_registers[i]);
}
g_led_control_registers_update_required = false;
M drivers/led/issi/is31fl3218.h => drivers/led/issi/is31fl3218.h +8 -0
@@ 21,6 21,14 @@
#include "progmem.h"
#include "util.h"
+#define IS31FL3218_REG_SHUTDOWN 0x00
+#define IS31FL3218_REG_PWM 0x01
+#define IS31FL3218_REG_LED_CONTROL_1 0x13
+#define IS31FL3218_REG_LED_CONTROL_2 0x14
+#define IS31FL3218_REG_LED_CONTROL_3 0x15
+#define IS31FL3218_REG_UPDATE 0x16
+#define IS31FL3218_REG_RESET 0x17
+
#define IS31FL3218_I2C_ADDRESS 0x54
#if defined(RGB_MATRIX_IS31FL3218)
M drivers/led/issi/is31fl3731-simple.c => drivers/led/issi/is31fl3731-simple.c +10 -30
@@ 22,26 22,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3731_REG_CONFIG 0x00
-#define IS31FL3731_REG_CONFIG_PICTUREMODE 0x00
-#define IS31FL3731_REG_CONFIG_AUTOPLAYMODE 0x08
-#define IS31FL3731_REG_CONFIG_AUDIOPLAYMODE 0x18
-
-#define IS31FL3731_CONF_PICTUREMODE 0x00
-#define IS31FL3731_CONF_AUTOFRAMEMODE 0x04
-#define IS31FL3731_CONF_AUDIOMODE 0x08
-
-#define IS31FL3731_REG_PICTUREFRAME 0x01
-
-// Not defined in the datasheet -- See AN for IC
-#define IS31FL3731_REG_GHOST_IMAGE_PREVENTION 0xC2 // Set bit 4 to enable de-ghosting
-
-#define IS31FL3731_REG_SHUTDOWN 0x0A
-#define IS31FL3731_REG_AUDIOSYNC 0x06
-
-#define IS31FL3731_COMMANDREGISTER 0xFD
-#define IS31FL3731_BANK_FUNCTIONREG 0x0B // helpfully called 'page nine'
-
#define IS31FL3731_PWM_REGISTER_COUNT 144
#define IS31FL3731_LED_CONTROL_REGISTER_COUNT 18
@@ 144,26 124,26 @@ void is31fl3731_init(uint8_t addr) {
// then disable software shutdown.
// select "function register" bank
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, IS31FL3731_BANK_FUNCTIONREG);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FUNCTION);
// enable software shutdown
- is31fl3731_write_register(addr, IS31FL3731_REG_SHUTDOWN, 0x00);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_SHUTDOWN, 0x00);
#ifdef IS31FL3731_DEGHOST // set to enable de-ghosting of the array
- is31fl3731_write_register(addr, IS31FL3731_REG_GHOST_IMAGE_PREVENTION, 0x10);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_GHOST_IMAGE_PREVENTION, IS31FL3731_GHOST_IMAGE_PREVENTION_GEN);
#endif
// this delay was copied from other drivers, might not be needed
wait_ms(10);
// picture mode
- is31fl3731_write_register(addr, IS31FL3731_REG_CONFIG, IS31FL3731_REG_CONFIG_PICTUREMODE);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_CONFIG, IS31FL3731_CONFIG_MODE_PICTURE);
// display frame 0
- is31fl3731_write_register(addr, IS31FL3731_REG_PICTUREFRAME, 0x00);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_PICTURE_DISPLAY, 0x00);
// audio sync off
- is31fl3731_write_register(addr, IS31FL3731_REG_AUDIOSYNC, 0x00);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_AUDIO_SYNC, 0x00);
// select bank 0
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, 0);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FRAME_1);
// turn off all LEDs in the LED control register
for (int i = 0; i < IS31FL3731_LED_CONTROL_REGISTER_COUNT; i++) {
@@ 181,15 161,15 @@ void is31fl3731_init(uint8_t addr) {
}
// select "function register" bank
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, IS31FL3731_BANK_FUNCTIONREG);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FUNCTION);
// disable software shutdown
- is31fl3731_write_register(addr, IS31FL3731_REG_SHUTDOWN, 0x01);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_SHUTDOWN, 0x01);
// select bank 0 and leave it selected.
// most usage after initialization is just writing PWM buffers in bank 0
// as there's not much point in double-buffering
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, 0);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FRAME_1);
}
void is31fl3731_set_value(int index, uint8_t value) {
M drivers/led/issi/is31fl3731-simple.h => drivers/led/issi/is31fl3731-simple.h +24 -0
@@ 50,6 50,30 @@
#define g_is31_leds g_is31fl3731_leds
// ========
+#define IS31FL3731_REG_COMMAND 0xFD
+#define IS31FL3731_COMMAND_FRAME_1 0x00
+#define IS31FL3731_COMMAND_FRAME_2 0x01
+#define IS31FL3731_COMMAND_FRAME_3 0x02
+#define IS31FL3731_COMMAND_FRAME_4 0x03
+#define IS31FL3731_COMMAND_FRAME_5 0x04
+#define IS31FL3731_COMMAND_FRAME_6 0x05
+#define IS31FL3731_COMMAND_FRAME_7 0x06
+#define IS31FL3731_COMMAND_FRAME_8 0x07
+#define IS31FL3731_COMMAND_FUNCTION 0x0B
+
+#define IS31FL3731_FUNCTION_REG_CONFIG 0x00
+#define IS31FL3731_CONFIG_MODE_PICTURE 0x00
+#define IS31FL3731_CONFIG_MODE_AUTO_PLAY 0x08
+#define IS31FL3731_CONFIG_MODE_AUDIO_PLAY 0x18
+
+#define IS31FL3731_FUNCTION_REG_PICTURE_DISPLAY 0x01
+#define IS31FL3731_FUNCTION_REG_AUDIO_SYNC 0x06
+#define IS31FL3731_FUNCTION_REG_SHUTDOWN 0x0A
+
+// Not defined in the datasheet -- See AN for IC
+#define IS31FL3731_FUNCTION_REG_GHOST_IMAGE_PREVENTION 0xC2
+#define IS31FL3731_GHOST_IMAGE_PREVENTION_GEN 0x10
+
#define IS31FL3731_I2C_ADDRESS_GND 0x74
#define IS31FL3731_I2C_ADDRESS_SCL 0x75
#define IS31FL3731_I2C_ADDRESS_SDA 0x76
M drivers/led/issi/is31fl3731.c => drivers/led/issi/is31fl3731.c +10 -30
@@ 21,26 21,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3731_REG_CONFIG 0x00
-#define IS31FL3731_REG_CONFIG_PICTUREMODE 0x00
-#define IS31FL3731_REG_CONFIG_AUTOPLAYMODE 0x08
-#define IS31FL3731_REG_CONFIG_AUDIOPLAYMODE 0x18
-
-#define IS31FL3731_CONF_PICTUREMODE 0x00
-#define IS31FL3731_CONF_AUTOFRAMEMODE 0x04
-#define IS31FL3731_CONF_AUDIOMODE 0x08
-
-#define IS31FL3731_REG_PICTUREFRAME 0x01
-
-// Not defined in the datasheet -- See AN for IC
-#define IS31FL3731_REG_GHOST_IMAGE_PREVENTION 0xC2 // Set bit 4 to enable de-ghosting
-
-#define IS31FL3731_REG_SHUTDOWN 0x0A
-#define IS31FL3731_REG_AUDIOSYNC 0x06
-
-#define IS31FL3731_COMMANDREGISTER 0xFD
-#define IS31FL3731_BANK_FUNCTIONREG 0x0B // helpfully called 'page nine'
-
#define IS31FL3731_PWM_REGISTER_COUNT 144
#define IS31FL3731_LED_CONTROL_REGISTER_COUNT 18
@@ 141,26 121,26 @@ void is31fl3731_init(uint8_t addr) {
// then disable software shutdown.
// select "function register" bank
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, IS31FL3731_BANK_FUNCTIONREG);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FUNCTION);
// enable software shutdown
- is31fl3731_write_register(addr, IS31FL3731_REG_SHUTDOWN, 0x00);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_SHUTDOWN, 0x00);
#ifdef IS31FL3731_DEGHOST // set to enable de-ghosting of the array
- is31fl3731_write_register(addr, IS31FL3731_REG_GHOST_IMAGE_PREVENTION, 0x10);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_GHOST_IMAGE_PREVENTION, IS31FL3731_GHOST_IMAGE_PREVENTION_GEN);
#endif
// this delay was copied from other drivers, might not be needed
wait_ms(10);
// picture mode
- is31fl3731_write_register(addr, IS31FL3731_REG_CONFIG, IS31FL3731_REG_CONFIG_PICTUREMODE);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_CONFIG, IS31FL3731_CONFIG_MODE_PICTURE);
// display frame 0
- is31fl3731_write_register(addr, IS31FL3731_REG_PICTUREFRAME, 0x00);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_PICTURE_DISPLAY, 0x00);
// audio sync off
- is31fl3731_write_register(addr, IS31FL3731_REG_AUDIOSYNC, 0x00);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_AUDIO_SYNC, 0x00);
// select bank 0
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, 0);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FRAME_1);
// turn off all LEDs in the LED control register
for (int i = 0; i < IS31FL3731_LED_CONTROL_REGISTER_COUNT; i++) {
@@ 178,15 158,15 @@ void is31fl3731_init(uint8_t addr) {
}
// select "function register" bank
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, IS31FL3731_BANK_FUNCTIONREG);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FUNCTION);
// disable software shutdown
- is31fl3731_write_register(addr, IS31FL3731_REG_SHUTDOWN, 0x01);
+ is31fl3731_write_register(addr, IS31FL3731_FUNCTION_REG_SHUTDOWN, 0x01);
// select bank 0 and leave it selected.
// most usage after initialization is just writing PWM buffers in bank 0
// as there's not much point in double-buffering
- is31fl3731_write_register(addr, IS31FL3731_COMMANDREGISTER, 0);
+ is31fl3731_write_register(addr, IS31FL3731_REG_COMMAND, IS31FL3731_COMMAND_FRAME_1);
}
void is31fl3731_set_color(int index, uint8_t red, uint8_t green, uint8_t blue) {
M drivers/led/issi/is31fl3731.h => drivers/led/issi/is31fl3731.h +24 -0
@@ 49,6 49,30 @@
#define g_is31_leds g_is31fl3731_leds
// ========
+#define IS31FL3731_REG_COMMAND 0xFD
+#define IS31FL3731_COMMAND_FRAME_1 0x00
+#define IS31FL3731_COMMAND_FRAME_2 0x01
+#define IS31FL3731_COMMAND_FRAME_3 0x02
+#define IS31FL3731_COMMAND_FRAME_4 0x03
+#define IS31FL3731_COMMAND_FRAME_5 0x04
+#define IS31FL3731_COMMAND_FRAME_6 0x05
+#define IS31FL3731_COMMAND_FRAME_7 0x06
+#define IS31FL3731_COMMAND_FRAME_8 0x07
+#define IS31FL3731_COMMAND_FUNCTION 0x0B
+
+#define IS31FL3731_FUNCTION_REG_CONFIG 0x00
+#define IS31FL3731_CONFIG_MODE_PICTURE 0x00
+#define IS31FL3731_CONFIG_MODE_AUTO_PLAY 0x08
+#define IS31FL3731_CONFIG_MODE_AUDIO_PLAY 0x18
+
+#define IS31FL3731_FUNCTION_REG_PICTURE_DISPLAY 0x01
+#define IS31FL3731_FUNCTION_REG_AUDIO_SYNC 0x06
+#define IS31FL3731_FUNCTION_REG_SHUTDOWN 0x0A
+
+// Not defined in the datasheet -- See AN for IC
+#define IS31FL3731_FUNCTION_REG_GHOST_IMAGE_PREVENTION 0xC2
+#define IS31FL3731_GHOST_IMAGE_PREVENTION_GEN 0x10
+
#define IS31FL3731_I2C_ADDRESS_GND 0x74
#define IS31FL3731_I2C_ADDRESS_SCL 0x75
#define IS31FL3731_I2C_ADDRESS_SDA 0x76
M drivers/led/issi/is31fl3733-simple.c => drivers/led/issi/is31fl3733-simple.c +16 -32
@@ 23,22 23,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3733_COMMANDREGISTER 0xFD
-#define IS31FL3733_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3733_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3733_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3733_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3733_PAGE_PWM 0x01 // PG1
-#define IS31FL3733_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3733_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3733_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3733_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3733_REG_RESET 0x11 // PG3
-#define IS31FL3733_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3733_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3733_PWM_REGISTER_COUNT 192
#define IS31FL3733_LED_CONTROL_REGISTER_COUNT 24
@@ 62,8 46,8 @@
# define IS31FL3733_CSPULLDOWN IS31FL3733_PDR_0_OHM
#endif
-#ifndef IS31FL3733_GLOBALCURRENT
-# define IS31FL3733_GLOBALCURRENT 0xFF
+#ifndef IS31FL3733_GLOBAL_CURRENT
+# define IS31FL3733_GLOBAL_CURRENT 0xFF
#endif
#ifndef IS31FL3733_SYNC_1
@@ 180,20 164,20 @@ void is31fl3733_init(uint8_t addr, uint8_t sync) {
// Sync is passed so set it according to the datasheet.
// Unlock the command register.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_LEDCONTROL);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3733_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3733_write_register(addr, i, 0x00);
}
// Unlock the command register.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_PWM);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3733_PWM_REGISTER_COUNT; i++) {
@@ 201,18 185,18 @@ void is31fl3733_init(uint8_t addr, uint8_t sync) {
}
// Unlock the command register.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_FUNCTION);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3733_write_register(addr, IS31FL3733_REG_SW_PULLUP, IS31FL3733_SW_PULLUP);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_SW_PULLUP, IS31FL3733_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3733_write_register(addr, IS31FL3733_REG_CS_PULLDOWN, IS31FL3733_CS_PULLDOWN);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_CS_PULLDOWN, IS31FL3733_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3733_write_register(addr, IS31FL3733_REG_GLOBALCURRENT, IS31FL3733_GLOBALCURRENT);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3733_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3733_write_register(addr, IS31FL3733_REG_CONFIGURATION, ((sync & 0b11) << 6) | ((IS31FL3733_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_CONFIGURATION, ((sync & 0b11) << 6) | ((IS31FL3733_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 256,8 240,8 @@ void is31fl3733_set_led_control_register(uint8_t index, bool value) {
void is31fl3733_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_PWM);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_PWM);
// If any of the transactions fail we risk writing dirty PG0,
// refresh page 0 just in case.
@@ 271,8 255,8 @@ void is31fl3733_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3733_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_LEDCONTROL);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3733_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3733_write_register(addr, i, g_led_control_registers[index][i]);
}
M drivers/led/issi/is31fl3733-simple.h => drivers/led/issi/is31fl3733-simple.h +20 -1
@@ 42,7 42,7 @@
# define IS31FL3733_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3733_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3733_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define is31_led is31fl3733_led_t
@@ 57,6 57,25 @@
#define PUR_32KR IS31FL3733_PUR_32K_OHM
// ========
+#define IS31FL3733_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3733_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3733_REG_COMMAND 0xFD
+
+#define IS31FL3733_COMMAND_LED_CONTROL 0x00
+#define IS31FL3733_COMMAND_PWM 0x01
+#define IS31FL3733_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3733_COMMAND_FUNCTION 0x03
+
+#define IS31FL3733_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3733_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3733_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3733_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3733_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3733_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3733_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3733_I2C_ADDRESS_GND_GND 0x50
#define IS31FL3733_I2C_ADDRESS_GND_SCL 0x51
#define IS31FL3733_I2C_ADDRESS_GND_SDA 0x52
M drivers/led/issi/is31fl3733.c => drivers/led/issi/is31fl3733.c +16 -32
@@ 22,22 22,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3733_COMMANDREGISTER 0xFD
-#define IS31FL3733_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3733_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3733_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3733_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3733_PAGE_PWM 0x01 // PG1
-#define IS31FL3733_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3733_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3733_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3733_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3733_REG_RESET 0x11 // PG3
-#define IS31FL3733_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3733_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3733_PWM_REGISTER_COUNT 192
#define IS31FL3733_LED_CONTROL_REGISTER_COUNT 24
@@ 61,8 45,8 @@
# define IS31FL3733_CS_PULLDOWN IS31FL3733_PDR_0_OHM
#endif
-#ifndef IS31FL3733_GLOBALCURRENT
-# define IS31FL3733_GLOBALCURRENT 0xFF
+#ifndef IS31FL3733_GLOBAL_CURRENT
+# define IS31FL3733_GLOBAL_CURRENT 0xFF
#endif
#ifndef IS31FL3733_SYNC_1
@@ 179,20 163,20 @@ void is31fl3733_init(uint8_t addr, uint8_t sync) {
// Sync is passed so set it according to the datasheet.
// Unlock the command register.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_LEDCONTROL);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3733_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3733_write_register(addr, i, 0x00);
}
// Unlock the command register.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_PWM);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3733_PWM_REGISTER_COUNT; i++) {
@@ 200,18 184,18 @@ void is31fl3733_init(uint8_t addr, uint8_t sync) {
}
// Unlock the command register.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_FUNCTION);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3733_write_register(addr, IS31FL3733_REG_SW_PULLUP, IS31FL3733_SW_PULLUP);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_SW_PULLUP, IS31FL3733_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3733_write_register(addr, IS31FL3733_REG_CS_PULLDOWN, IS31FL3733_CS_PULLDOWN);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_CS_PULLDOWN, IS31FL3733_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3733_write_register(addr, IS31FL3733_REG_GLOBALCURRENT, IS31FL3733_GLOBALCURRENT);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3733_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3733_write_register(addr, IS31FL3733_REG_CONFIGURATION, ((sync & 0b11) << 6) | ((IS31FL3733_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3733_write_register(addr, IS31FL3733_FUNCTION_REG_CONFIGURATION, ((sync & 0b11) << 6) | ((IS31FL3733_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 271,8 255,8 @@ void is31fl3733_set_led_control_register(uint8_t index, bool red, bool green, bo
void is31fl3733_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1.
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_PWM);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_PWM);
// If any of the transactions fail we risk writing dirty PG0,
// refresh page 0 just in case.
@@ 286,8 270,8 @@ void is31fl3733_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3733_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3733_write_register(addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_LEDCONTROL);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3733_write_register(addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3733_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3733_write_register(addr, i, g_led_control_registers[index][i]);
}
M drivers/led/issi/is31fl3733.h => drivers/led/issi/is31fl3733.h +20 -1
@@ 65,7 65,7 @@
# define IS31FL3733_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3733_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3733_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define is31_led is31fl3733_led_t
@@ 80,6 80,25 @@
#define PUR_32KR IS31FL3733_PUR_32K_OHM
// ========
+#define IS31FL3733_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3733_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3733_REG_COMMAND 0xFD
+
+#define IS31FL3733_COMMAND_LED_CONTROL 0x00
+#define IS31FL3733_COMMAND_PWM 0x01
+#define IS31FL3733_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3733_COMMAND_FUNCTION 0x03
+
+#define IS31FL3733_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3733_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3733_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3733_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3733_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3733_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3733_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3733_I2C_ADDRESS_GND_GND 0x50
#define IS31FL3733_I2C_ADDRESS_GND_SCL 0x51
#define IS31FL3733_I2C_ADDRESS_GND_SDA 0x52
M drivers/led/issi/is31fl3736-simple.c => drivers/led/issi/is31fl3736-simple.c +16 -32
@@ 20,22 20,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3736_COMMANDREGISTER 0xFD
-#define IS31FL3736_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3736_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3736_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3736_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3736_PAGE_PWM 0x01 // PG1
-#define IS31FL3736_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3736_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3736_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3736_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3736_REG_RESET 0x11 // PG3
-#define IS31FL3736_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3736_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3736_PWM_REGISTER_COUNT 192 // actually 96
#define IS31FL3736_LED_CONTROL_REGISTER_COUNT 24
@@ 59,8 43,8 @@
# define IS31FL3736_CS_PULLDOWN IS31FL3736_PDR_0_OHM
#endif
-#ifndef IS31FL3736_GLOBALCURRENT
-# define IS31FL3736_GLOBALCURRENT 0xFF
+#ifndef IS31FL3736_GLOBAL_CURRENT
+# define IS31FL3736_GLOBAL_CURRENT 0xFF
#endif
// Transfer buffer for TWITransmitData()
@@ 152,20 136,20 @@ void is31fl3736_init(uint8_t addr) {
// then disable software shutdown.
// Unlock the command register.
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_LEDCONTROL);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3736_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3736_write_register(addr, i, 0x00);
}
// Unlock the command register.
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_PWM);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3736_PWM_REGISTER_COUNT; i++) {
@@ 173,18 157,18 @@ void is31fl3736_init(uint8_t addr) {
}
// Unlock the command register.
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_FUNCTION);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3736_write_register(addr, IS31FL3736_REG_SW_PULLUP, IS31FL3736_SW_PULLUP);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_SW_PULLUP, IS31FL3736_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3736_write_register(addr, IS31FL3736_REG_CS_PULLDOWN, IS31FL3736_CS_PULLDOWN);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_CS_PULLDOWN, IS31FL3736_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3736_write_register(addr, IS31FL3736_REG_GLOBALCURRENT, IS31FL3736_GLOBALCURRENT);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3736_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3736_write_register(addr, IS31FL3736_REG_CONFIGURATION, ((IS31FL3736_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_CONFIGURATION, ((IS31FL3736_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 234,8 218,8 @@ void is31fl3736_set_led_control_register(uint8_t index, bool value) {
void is31fl3736_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_PWM);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_PWM);
is31fl3736_write_pwm_buffer(addr, g_pwm_buffer[index]);
g_pwm_buffer_update_required[index] = false;
@@ 245,8 229,8 @@ void is31fl3736_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3736_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_LEDCONTROL);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3736_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3736_write_register(addr, i, g_led_control_registers[index][i]);
}
M drivers/led/issi/is31fl3736-simple.h => drivers/led/issi/is31fl3736-simple.h +20 -1
@@ 36,7 36,7 @@
# define IS31FL3736_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3736_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3736_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define is31_led is31fl3736_led_t
@@ 52,6 52,25 @@
#define PUR_32KR IS31FL3736_PUR_32K_OHM
// ========
+#define IS31FL3736_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3736_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3736_REG_COMMAND 0xFD
+
+#define IS31FL3736_COMMAND_LED_CONTROL 0x00
+#define IS31FL3736_COMMAND_PWM 0x01
+#define IS31FL3736_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3736_COMMAND_FUNCTION 0x03
+
+#define IS31FL3736_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3736_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3736_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3736_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3736_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3736_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3736_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3736_I2C_ADDRESS_GND_GND 0x50
#define IS31FL3736_I2C_ADDRESS_GND_SCL 0x51
#define IS31FL3736_I2C_ADDRESS_GND_SDA 0x52
M drivers/led/issi/is31fl3736.c => drivers/led/issi/is31fl3736.c +16 -32
@@ 20,22 20,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3736_COMMANDREGISTER 0xFD
-#define IS31FL3736_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3736_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3736_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3736_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3736_PAGE_PWM 0x01 // PG1
-#define IS31FL3736_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3736_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3736_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3736_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3736_REG_RESET 0x11 // PG3
-#define IS31FL3736_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3736_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3736_PWM_REGISTER_COUNT 192 // actually 96
#define IS31FL3736_LED_CONTROL_REGISTER_COUNT 24
@@ 59,8 43,8 @@
# define IS31FL3736_CS_PULLDOWN IS31FL3736_PDR_0_OHM
#endif
-#ifndef IS31FL3736_GLOBALCURRENT
-# define IS31FL3736_GLOBALCURRENT 0xFF
+#ifndef IS31FL3736_GLOBAL_CURRENT
+# define IS31FL3736_GLOBAL_CURRENT 0xFF
#endif
// Transfer buffer for TWITransmitData()
@@ 152,20 136,20 @@ void is31fl3736_init(uint8_t addr) {
// then disable software shutdown.
// Unlock the command register.
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_LEDCONTROL);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_REG_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3736_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3736_write_register(addr, i, 0x00);
}
// Unlock the command register.
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITELOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_PWM);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3736_PWM_REGISTER_COUNT; i++) {
@@ 173,18 157,18 @@ void is31fl3736_init(uint8_t addr) {
}
// Unlock the command register.
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_FUNCTION);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3736_write_register(addr, IS31FL3736_REG_SW_PULLUP, IS31FL3736_SW_PULLUP);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_SW_PULLUP, IS31FL3736_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3736_write_register(addr, IS31FL3736_REG_CS_PULLDOWN, IS31FL3736_CS_PULLDOWN);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_CS_PULLDOWN, IS31FL3736_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3736_write_register(addr, IS31FL3736_REG_GLOBALCURRENT, IS31FL3736_GLOBALCURRENT);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3736_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3736_write_register(addr, IS31FL3736_REG_CONFIGURATION, ((IS31FL3736_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3736_write_register(addr, IS31FL3736_FUNCTION_REG_CONFIGURATION, ((IS31FL3736_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 251,8 235,8 @@ void is31fl3736_set_led_control_register(uint8_t index, bool red, bool green, bo
void is31fl3736_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_PWM);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_PWM);
is31fl3736_write_pwm_buffer(addr, g_pwm_buffer[index]);
g_pwm_buffer_update_required[index] = false;
@@ 262,8 246,8 @@ void is31fl3736_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3736_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3736_write_register(addr, IS31FL3736_COMMANDREGISTER, IS31FL3736_PAGE_LEDCONTROL);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND_WRITE_LOCK, IS31FL3736_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3736_write_register(addr, IS31FL3736_REG_COMMAND, IS31FL3736_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3736_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3736_write_register(addr, i, g_led_control_registers[index][i]);
}
M drivers/led/issi/is31fl3736.h => drivers/led/issi/is31fl3736.h +20 -1
@@ 48,7 48,7 @@
# define IS31FL3736_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3736_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3736_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define is31_led is31fl3736_led_t
@@ 64,6 64,25 @@
#define PUR_32KR IS31FL3736_PUR_32K_OHM
// ========
+#define IS31FL3736_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3736_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3736_REG_COMMAND 0xFD
+
+#define IS31FL3736_COMMAND_LED_CONTROL 0x00
+#define IS31FL3736_COMMAND_PWM 0x01
+#define IS31FL3736_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3736_COMMAND_FUNCTION 0x03
+
+#define IS31FL3736_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3736_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3736_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3736_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3736_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3736_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3736_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3736_I2C_ADDRESS_GND_GND 0x50
#define IS31FL3736_I2C_ADDRESS_GND_SCL 0x51
#define IS31FL3736_I2C_ADDRESS_GND_SDA 0x52
M drivers/led/issi/is31fl3737-simple.c => drivers/led/issi/is31fl3737-simple.c +16 -32
@@ 22,22 22,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3737_COMMANDREGISTER 0xFD
-#define IS31FL3737_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3737_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3737_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3737_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3737_PAGE_PWM 0x01 // PG1
-#define IS31FL3737_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3737_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3737_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3737_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3737_REG_RESET 0x11 // PG3
-#define IS31FL3737_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3737_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3737_PWM_REGISTER_COUNT 192 // actually 144
#define IS31FL3737_LED_CONTROL_REGISTER_COUNT 24
@@ 61,8 45,8 @@
# define IS31FL3737_CS_PULLDOWN IS31FL3737_PDR_0_OHM
#endif
-#ifndef IS31FL3737_GLOBALCURRENT
-# define IS31FL3737_GLOBALCURRENT 0xFF
+#ifndef IS31FL3737_GLOBAL_CURRENT
+# define IS31FL3737_GLOBAL_CURRENT 0xFF
#endif
// Transfer buffer for TWITransmitData()
@@ 155,20 139,20 @@ void is31fl3737_init(uint8_t addr) {
// then disable software shutdown.
// Unlock the command register.
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_LEDCONTROL);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3737_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3737_write_register(addr, i, 0x00);
}
// Unlock the command register.
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_PWM);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3737_PWM_REGISTER_COUNT; i++) {
@@ 176,18 160,18 @@ void is31fl3737_init(uint8_t addr) {
}
// Unlock the command register.
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_FUNCTION);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3737_write_register(addr, IS31FL3737_REG_SW_PULLUP, IS31FL3737_SW_PULLUP);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_SW_PULLUP, IS31FL3737_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3737_write_register(addr, IS31FL3737_REG_CS_PULLDOWN, IS31FL3737_CS_PULLDOWN);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_CS_PULLDOWN, IS31FL3737_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3737_write_register(addr, IS31FL3737_REG_GLOBALCURRENT, IS31FL3737_GLOBALCURRENT);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3737_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3737_write_register(addr, IS31FL3737_REG_CONFIGURATION, ((IS31FL3737_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_CONFIGURATION, ((IS31FL3737_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 231,8 215,8 @@ void is31fl3737_set_led_control_register(uint8_t index, bool value) {
void is31fl3737_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_PWM);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_PWM);
is31fl3737_write_pwm_buffer(addr, g_pwm_buffer[index]);
g_pwm_buffer_update_required[index] = false;
@@ 242,8 226,8 @@ void is31fl3737_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3737_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_LEDCONTROL);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3737_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3737_write_register(addr, i, g_led_control_registers[index][i]);
}
M drivers/led/issi/is31fl3737-simple.h => drivers/led/issi/is31fl3737-simple.h +20 -1
@@ 41,7 41,7 @@
# define IS31FL3737_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3737_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3737_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define PUR_0R IS31FL3737_PUR_0_OHM
@@ 54,6 54,25 @@
#define PUR_32KR IS31FL3737_PUR_32K_OHM
// ========
+#define IS31FL3737_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3737_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3737_REG_COMMAND 0xFD
+
+#define IS31FL3737_COMMAND_LED_CONTROL 0x00
+#define IS31FL3737_COMMAND_PWM 0x01
+#define IS31FL3737_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3737_COMMAND_FUNCTION 0x03
+
+#define IS31FL3737_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3737_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3737_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3737_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3737_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3737_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3737_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3737_I2C_ADDRESS_GND 0x50
#define IS31FL3737_I2C_ADDRESS_SCL 0x55
#define IS31FL3737_I2C_ADDRESS_SDA 0x5A
M drivers/led/issi/is31fl3737.c => drivers/led/issi/is31fl3737.c +16 -32
@@ 22,22 22,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3737_COMMANDREGISTER 0xFD
-#define IS31FL3737_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3737_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3737_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3737_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3737_PAGE_PWM 0x01 // PG1
-#define IS31FL3737_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3737_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3737_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3737_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3737_REG_RESET 0x11 // PG3
-#define IS31FL3737_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3737_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3737_PWM_REGISTER_COUNT 192 // actually 144
#define IS31FL3737_LED_CONTROL_REGISTER_COUNT 24
@@ 61,8 45,8 @@
# define IS31FL3737_CS_PULLDOWN IS31FL3737_PDR_0_OHM
#endif
-#ifndef IS31FL3737_GLOBALCURRENT
-# define IS31FL3737_GLOBALCURRENT 0xFF
+#ifndef IS31FL3737_GLOBAL_CURRENT
+# define IS31FL3737_GLOBAL_CURRENT 0xFF
#endif
// Transfer buffer for TWITransmitData()
@@ 155,20 139,20 @@ void is31fl3737_init(uint8_t addr) {
// then disable software shutdown.
// Unlock the command register.
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_LEDCONTROL);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3737_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3737_write_register(addr, i, 0x00);
}
// Unlock the command register.
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_PWM);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3737_PWM_REGISTER_COUNT; i++) {
@@ 176,18 160,18 @@ void is31fl3737_init(uint8_t addr) {
}
// Unlock the command register.
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_FUNCTION);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3737_write_register(addr, IS31FL3737_REG_SW_PULLUP, IS31FL3737_SW_PULLUP);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_SW_PULLUP, IS31FL3737_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3737_write_register(addr, IS31FL3737_REG_CS_PULLDOWN, IS31FL3737_CS_PULLDOWN);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_CS_PULLDOWN, IS31FL3737_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3737_write_register(addr, IS31FL3737_REG_GLOBALCURRENT, IS31FL3737_GLOBALCURRENT);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3737_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3737_write_register(addr, IS31FL3737_REG_CONFIGURATION, ((IS31FL3737_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3737_write_register(addr, IS31FL3737_FUNCTION_REG_CONFIGURATION, ((IS31FL3737_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 247,8 231,8 @@ void is31fl3737_set_led_control_register(uint8_t index, bool red, bool green, bo
void is31fl3737_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_PWM);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_PWM);
is31fl3737_write_pwm_buffer(addr, g_pwm_buffer[index]);
g_pwm_buffer_update_required[index] = false;
@@ 258,8 242,8 @@ void is31fl3737_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3737_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3737_write_register(addr, IS31FL3737_COMMANDREGISTER, IS31FL3737_PAGE_LEDCONTROL);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND_WRITE_LOCK, IS31FL3737_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3737_write_register(addr, IS31FL3737_REG_COMMAND, IS31FL3737_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3737_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3737_write_register(addr, i, g_led_control_registers[index][i]);
}
M drivers/led/issi/is31fl3737.h => drivers/led/issi/is31fl3737.h +20 -1
@@ 53,7 53,7 @@
# define IS31FL3737_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3737_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3737_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define is31_led is31fl3737_led_t
@@ 69,6 69,25 @@
#define PUR_32KR IS31FL3737_PUR_32K_OHM
// ========
+#define IS31FL3737_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3737_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3737_REG_COMMAND 0xFD
+
+#define IS31FL3737_COMMAND_LED_CONTROL 0x00
+#define IS31FL3737_COMMAND_PWM 0x01
+#define IS31FL3737_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3737_COMMAND_FUNCTION 0x03
+
+#define IS31FL3737_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3737_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3737_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3737_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3737_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3737_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3737_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3737_I2C_ADDRESS_GND 0x50
#define IS31FL3737_I2C_ADDRESS_SCL 0x55
#define IS31FL3737_I2C_ADDRESS_SDA 0x5A
M drivers/led/issi/is31fl3741-simple.c => drivers/led/issi/is31fl3741-simple.c +16 -34
@@ 22,24 22,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3741_COMMANDREGISTER 0xFD
-#define IS31FL3741_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3741_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3741_INTERRUPTSTATUSREGISTER 0xF1
-#define IS31FL3741_IDREGISTER 0xFC
-
-#define IS31FL3741_PAGE_PWM0 0x00 // PG0
-#define IS31FL3741_PAGE_PWM1 0x01 // PG1
-#define IS31FL3741_PAGE_SCALING_0 0x02 // PG2
-#define IS31FL3741_PAGE_SCALING_1 0x03 // PG3
-#define IS31FL3741_PAGE_FUNCTION 0x04 // PG4
-
-#define IS31FL3741_REG_CONFIGURATION 0x00 // PG4
-#define IS31FL3741_REG_GLOBALCURRENT 0x01 // PG4
-#define IS31FL3741_REG_PULLDOWNUP 0x02 // PG4
-#define IS31FL3741_REG_PWM_FREQUENCY 0x36 // PG4
-#define IS31FL3741_REG_RESET 0x3F // PG4
-
#define IS31FL3741_PWM_REGISTER_COUNT 351
#ifndef IS31FL3741_I2C_TIMEOUT
@@ 66,8 48,8 @@
# define IS31FL3741_CS_PULLDOWN IS31FL3741_PDR_32K_OHM
#endif
-#ifndef IS31FL3741_GLOBALCURRENT
-# define IS31FL3741_GLOBALCURRENT 0xFF
+#ifndef IS31FL3741_GLOBAL_CURRENT
+# define IS31FL3741_GLOBAL_CURRENT 0xFF
#endif
// Transfer buffer for TWITransmitData()
@@ 104,8 86,8 @@ bool is31fl3741_write_pwm_buffer(uint8_t addr, uint8_t *pwm_buffer) {
for (int i = 0; i < 342; i += 18) {
if (i == 180) {
// unlock the command register and select PG1
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_PWM1);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_PWM_1);
}
g_twi_transfer_buffer[0] = i % 180;
@@ 181,20 163,20 @@ void is31fl3741_init(uint8_t addr) {
// Unlock the command register.
// Unlock the command register.
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
// Select PG4
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_FUNCTION);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_FUNCTION);
// Set to Normal operation
- is31fl3741_write_register(addr, IS31FL3741_REG_CONFIGURATION, IS31FL3741_CONFIGURATION);
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_CONFIGURATION, IS31FL3741_CONFIGURATION);
// Set Golbal Current Control Register
- is31fl3741_write_register(addr, IS31FL3741_REG_GLOBALCURRENT, IS31FL3741_GLOBALCURRENT);
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3741_GLOBAL_CURRENT);
// Set Pull up & Down for SWx CSy
- is31fl3741_write_register(addr, IS31FL3741_REG_PULLDOWNUP, ((IS31FL3741_CS_PULLDOWN << 4) | IS31FL3741_SW_PULLUP));
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_PULLDOWNUP, ((IS31FL3741_CS_PULLDOWN << 4) | IS31FL3741_SW_PULLUP));
// Set PWM frequency
- is31fl3741_write_register(addr, IS31FL3741_REG_PWM_FREQUENCY, (IS31FL3741_PWM_FREQUENCY & 0b1111));
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_PWM_FREQUENCY, (IS31FL3741_PWM_FREQUENCY & 0b1111));
// is31fl3741_update_led_scaling_registers(addr, 0xFF, 0xFF, 0xFF);
@@ 237,8 219,8 @@ void is31fl3741_set_led_control_register(uint8_t index, bool value) {
void is31fl3741_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// unlock the command register and select PG2
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_PWM0);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_PWM_0);
is31fl3741_write_pwm_buffer(addr, g_pwm_buffer[index]);
}
@@ 255,8 237,8 @@ void is31fl3741_set_pwm_buffer(const is31fl3741_led_t *pled, uint8_t value) {
void is31fl3741_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_scaling_registers_update_required[index]) {
// unlock the command register and select PG2
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_SCALING_0);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_SCALING_0);
// CS1_SW1 to CS30_SW6 are on PG2
for (int i = CS1_SW1; i <= CS30_SW6; ++i) {
@@ 264,8 246,8 @@ void is31fl3741_update_led_control_registers(uint8_t addr, uint8_t index) {
}
// unlock the command register and select PG3
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_SCALING_1);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_SCALING_1);
// CS1_SW7 to CS39_SW9 are on PG3
for (int i = CS1_SW7; i <= CS39_SW9; ++i) {
M drivers/led/issi/is31fl3741-simple.h => drivers/led/issi/is31fl3741-simple.h +22 -1
@@ 41,7 41,7 @@
# define IS31FL3741_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3741_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3741_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define PUR_0R IS31FL3741_PUR_0_OHM
@@ 54,6 54,27 @@
#define PUR_32KR IS31FL3741_PUR_32K_OHM
// ========
+#define IS31FL3741_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3741_REG_INTERRUPT_STATUS 0xF1
+#define IS31FL3741_REG_ID 0xFC
+
+#define IS31FL3741_REG_COMMAND 0xFD
+
+#define IS31FL3741_COMMAND_PWM_0 0x00
+#define IS31FL3741_COMMAND_PWM_1 0x01
+#define IS31FL3741_COMMAND_SCALING_0 0x02
+#define IS31FL3741_COMMAND_SCALING_1 0x03
+#define IS31FL3741_COMMAND_FUNCTION 0x04
+
+#define IS31FL3741_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3741_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3741_FUNCTION_REG_PULLDOWNUP 0x02
+#define IS31FL3741_FUNCTION_REG_PWM_FREQUENCY 0x36
+#define IS31FL3741_FUNCTION_REG_RESET 0x3F
+
+#define IS31FL3741_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3741_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3741_I2C_ADDRESS_GND 0x30
#define IS31FL3741_I2C_ADDRESS_SCL 0x31
#define IS31FL3741_I2C_ADDRESS_SDA 0x32
M drivers/led/issi/is31fl3741.c => drivers/led/issi/is31fl3741.c +16 -34
@@ 22,24 22,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3741_COMMANDREGISTER 0xFD
-#define IS31FL3741_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3741_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3741_INTERRUPTSTATUSREGISTER 0xF1
-#define IS31FL3741_IDREGISTER 0xFC
-
-#define IS31FL3741_PAGE_PWM0 0x00 // PG0
-#define IS31FL3741_PAGE_PWM1 0x01 // PG1
-#define IS31FL3741_PAGE_SCALING_0 0x02 // PG2
-#define IS31FL3741_PAGE_SCALING_1 0x03 // PG3
-#define IS31FL3741_PAGE_FUNCTION 0x04 // PG4
-
-#define IS31FL3741_REG_CONFIGURATION 0x00 // PG4
-#define IS31FL3741_REG_GLOBALCURRENT 0x01 // PG4
-#define IS31FL3741_REG_PULLDOWNUP 0x02 // PG4
-#define IS31FL3741_REG_PWM_FREQUENCY 0x36 // PG4
-#define IS31FL3741_REG_RESET 0x3F // PG4
-
#define IS31FL3741_PWM_REGISTER_COUNT 351
#ifndef IS31FL3741_I2C_TIMEOUT
@@ 66,8 48,8 @@
# define IS31FL3741_CS_PULLDOWN IS31FL3741_PDR_32K_OHM
#endif
-#ifndef IS31FL3741_GLOBALCURRENT
-# define IS31FL3741_GLOBALCURRENT 0xFF
+#ifndef IS31FL3741_GLOBAL_CURRENT
+# define IS31FL3741_GLOBAL_CURRENT 0xFF
#endif
// Transfer buffer for TWITransmitData()
@@ 104,8 86,8 @@ bool is31fl3741_write_pwm_buffer(uint8_t addr, uint8_t *pwm_buffer) {
for (int i = 0; i < 342; i += 18) {
if (i == 180) {
// unlock the command register and select PG1
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_PWM1);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_PWM_1);
}
g_twi_transfer_buffer[0] = i % 180;
@@ 181,20 163,20 @@ void is31fl3741_init(uint8_t addr) {
// Unlock the command register.
// Unlock the command register.
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
// Select PG4
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_FUNCTION);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_FUNCTION);
// Set to Normal operation
- is31fl3741_write_register(addr, IS31FL3741_REG_CONFIGURATION, IS31FL3741_CONFIGURATION);
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_CONFIGURATION, IS31FL3741_CONFIGURATION);
// Set Golbal Current Control Register
- is31fl3741_write_register(addr, IS31FL3741_REG_GLOBALCURRENT, IS31FL3741_GLOBALCURRENT);
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3741_GLOBAL_CURRENT);
// Set Pull up & Down for SWx CSy
- is31fl3741_write_register(addr, IS31FL3741_REG_PULLDOWNUP, ((IS31FL3741_CS_PULLDOWN << 4) | IS31FL3741_SW_PULLUP));
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_PULLDOWNUP, ((IS31FL3741_CS_PULLDOWN << 4) | IS31FL3741_SW_PULLUP));
// Set PWM frequency
- is31fl3741_write_register(addr, IS31FL3741_REG_PWM_FREQUENCY, (IS31FL3741_PWM_FREQUENCY & 0b1111));
+ is31fl3741_write_register(addr, IS31FL3741_FUNCTION_REG_PWM_FREQUENCY, (IS31FL3741_PWM_FREQUENCY & 0b1111));
// is31fl3741_update_led_scaling_registers(addr, 0xFF, 0xFF, 0xFF);
@@ 251,8 233,8 @@ void is31fl3741_set_led_control_register(uint8_t index, bool red, bool green, bo
void is31fl3741_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// unlock the command register and select PG2
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_PWM0);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_PWM_0);
is31fl3741_write_pwm_buffer(addr, g_pwm_buffer[index]);
}
@@ 271,8 253,8 @@ void is31fl3741_set_pwm_buffer(const is31fl3741_led_t *pled, uint8_t red, uint8_
void is31fl3741_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_scaling_registers_update_required[index]) {
// unlock the command register and select PG2
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_SCALING_0);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_SCALING_0);
// CS1_SW1 to CS30_SW6 are on PG2
for (int i = CS1_SW1; i <= CS30_SW6; ++i) {
@@ 280,8 262,8 @@ void is31fl3741_update_led_control_registers(uint8_t addr, uint8_t index) {
}
// unlock the command register and select PG3
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3741_write_register(addr, IS31FL3741_COMMANDREGISTER, IS31FL3741_PAGE_SCALING_1);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND_WRITE_LOCK, IS31FL3741_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3741_write_register(addr, IS31FL3741_REG_COMMAND, IS31FL3741_COMMAND_SCALING_1);
// CS1_SW7 to CS39_SW9 are on PG3
for (int i = CS1_SW7; i <= CS39_SW9; ++i) {
M drivers/led/issi/is31fl3741.h => drivers/led/issi/is31fl3741.h +22 -1
@@ 53,7 53,7 @@
# define IS31FL3741_CS_PULLDOWN ISSI_CSPULLUP
#endif
#ifdef ISSI_GLOBALCURRENT
-# define IS31FL3741_GLOBALCURRENT ISSI_GLOBALCURRENT
+# define IS31FL3741_GLOBAL_CURRENT ISSI_GLOBALCURRENT
#endif
#define is31_led is31fl3741_led_t
@@ 69,6 69,27 @@
#define PUR_32KR IS31FL3741_PUR_32K_OHM
// ========
+#define IS31FL3741_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3741_REG_INTERRUPT_STATUS 0xF1
+#define IS31FL3741_REG_ID 0xFC
+
+#define IS31FL3741_REG_COMMAND 0xFD
+
+#define IS31FL3741_COMMAND_PWM_0 0x00
+#define IS31FL3741_COMMAND_PWM_1 0x01
+#define IS31FL3741_COMMAND_SCALING_0 0x02
+#define IS31FL3741_COMMAND_SCALING_1 0x03
+#define IS31FL3741_COMMAND_FUNCTION 0x04
+
+#define IS31FL3741_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3741_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3741_FUNCTION_REG_PULLDOWNUP 0x02
+#define IS31FL3741_FUNCTION_REG_PWM_FREQUENCY 0x36
+#define IS31FL3741_FUNCTION_REG_RESET 0x3F
+
+#define IS31FL3741_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3741_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3741_I2C_ADDRESS_GND 0x30
#define IS31FL3741_I2C_ADDRESS_SCL 0x31
#define IS31FL3741_I2C_ADDRESS_SDA 0x32
M drivers/led/snled27351-simple.c => drivers/led/snled27351-simple.c +21 -21
@@ 29,7 29,7 @@
#endif
#ifndef SNLED27351_PHASE_CHANNEL
-# define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_12CHANNEL
+# define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_12_CHANNEL
#endif
#ifndef SNLED27351_CURRENT_TUNE
@@ 134,48 134,48 @@ void snled27351_init_drivers(void) {
void snled27351_init(uint8_t addr) {
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to shutdown mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_SHUT_DOWN_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_SHUTDOWN);
// Setting internal channel pulldown/pullup
- snled27351_write_register(addr, SNLED27351_REG_PDU, SNLED27351_MSKSET_CA_CB_CHANNEL);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_PULLDOWNUP, SNLED27351_PULLDOWNUP_ALL_ENABLED);
// Select number of scan phase
- snled27351_write_register(addr, SNLED27351_REG_SCAN_PHASE, SNLED27351_PHASE_CHANNEL);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SCAN_PHASE, SNLED27351_PHASE_CHANNEL);
// Setting PWM Delay Phase
- snled27351_write_register(addr, SNLED27351_REG_SLEW_RATE_CONTROL_MODE1, SNLED27351_MSKPWM_DELAY_PHASE_ENABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_1, SNLED27351_SLEW_RATE_CONTROL_MODE_1_PDP_ENABLE);
// Setting Driving/Sinking Channel Slew Rate
- snled27351_write_register(addr, SNLED27351_REG_SLEW_RATE_CONTROL_MODE2, SNLED27351_MSKDRIVING_SINKING_CHANNEL_SLEWRATE_ENABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_2, SNLED27351_SLEW_RATE_CONTROL_MODE_2_DSL_ENABLE | SNLED27351_SLEW_RATE_CONTROL_MODE_2_SSL_ENABLE);
// Setting Iref
- snled27351_write_register(addr, SNLED27351_REG_SOFTWARE_SLEEP, SNLED27351_MSKSLEEP_DISABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SLEEP, 0);
// Set LED CONTROL PAGE (Page 0)
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_CONTROL_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_LED_CONTROL);
for (int i = 0; i < SNLED27351_LED_CONTROL_ON_OFF_LENGTH; i++) {
snled27351_write_register(addr, i, 0x00);
}
// Set PWM PAGE (Page 1)
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_PWM_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_PWM);
for (int i = 0; i < SNLED27351_LED_CURRENT_TUNE_LENGTH; i++) {
snled27351_write_register(addr, i, 0x00);
}
// Set CURRENT PAGE (Page 4)
uint8_t current_tune_reg_list[SNLED27351_LED_CURRENT_TUNE_LENGTH] = SNLED27351_CURRENT_TUNE;
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_CURRENT_TUNE_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_CURRENT_TUNE);
for (int i = 0; i < SNLED27351_LED_CURRENT_TUNE_LENGTH; i++) {
snled27351_write_register(addr, i, current_tune_reg_list[i]);
}
// Enable LEDs ON/OFF
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_CONTROL_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_LED_CONTROL);
for (int i = 0; i < SNLED27351_LED_CONTROL_ON_OFF_LENGTH; i++) {
snled27351_write_register(addr, i, 0xFF);
}
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to normal mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_NORMAL_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_NORMAL);
}
void snled27351_set_value(int index, uint8_t value) {
@@ 215,7 215,7 @@ void snled27351_set_led_control_register(uint8_t index, bool value) {
void snled27351_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_PWM_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_PWM);
// If any of the transactions fail we risk writing dirty PG0,
// refresh page 0 just in case.
@@ 228,7 228,7 @@ void snled27351_update_pwm_buffers(uint8_t addr, uint8_t index) {
void snled27351_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_CONTROL_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_LED_CONTROL);
for (int i = 0; i < SNLED27351_LED_CONTROL_REGISTER_COUNT; i++) {
snled27351_write_register(addr, i, g_led_control_registers[index][i]);
}
@@ 251,16 251,16 @@ void snled27351_flush(void) {
void snled27351_sw_return_normal(uint8_t addr) {
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to normal mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_NORMAL_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_NORMAL);
}
void snled27351_sw_shutdown(uint8_t addr) {
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to shutdown mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_SHUT_DOWN_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_SHUTDOWN);
// Write SW Sleep Register
- snled27351_write_register(addr, SNLED27351_REG_SOFTWARE_SLEEP, SNLED27351_MSKSLEEP_ENABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SLEEP, SNLED27351_SOFTWARE_SLEEP_ENABLE);
}
M drivers/led/snled27351-simple.h => drivers/led/snled27351-simple.h +87 -98
@@ 35,23 35,98 @@
# define SNLED27351_CURRENT_TUNE CKLED2001_CURRENT_TUNE
#endif
-#define MSKPHASE_12CHANNEL SNLED27351_MSKPHASE_12CHANNEL
-#define MSKPHASE_11CHANNEL SNLED27351_MSKPHASE_11CHANNEL
-#define MSKPHASE_10CHANNEL SNLED27351_MSKPHASE_10CHANNEL
-#define MSKPHASE_9CHANNEL SNLED27351_MSKPHASE_9CHANNEL
-#define MSKPHASE_8CHANNEL SNLED27351_MSKPHASE_8CHANNEL
-#define MSKPHASE_7CHANNEL SNLED27351_MSKPHASE_7CHANNEL
-#define MSKPHASE_6CHANNEL SNLED27351_MSKPHASE_6CHANNEL
-#define MSKPHASE_5CHANNEL SNLED27351_MSKPHASE_5CHANNEL
-#define MSKPHASE_4CHANNEL SNLED27351_MSKPHASE_4CHANNEL
-#define MSKPHASE_3CHANNEL SNLED27351_MSKPHASE_3CHANNEL
-#define MSKPHASE_2CHANNEL SNLED27351_MSKPHASE_2CHANNEL
-#define MSKPHASE_1CHANNEL SNLED27351_MSKPHASE_1CHANNEL
+#define MSKPHASE_12CHANNEL SNLED27351_SCAN_PHASE_12_CHANNEL
+#define MSKPHASE_11CHANNEL SNLED27351_SCAN_PHASE_11_CHANNEL
+#define MSKPHASE_10CHANNEL SNLED27351_SCAN_PHASE_10_CHANNEL
+#define MSKPHASE_9CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
+#define MSKPHASE_8CHANNEL SNLED27351_SCAN_PHASE_8_CHANNEL
+#define MSKPHASE_7CHANNEL SNLED27351_SCAN_PHASE_7_CHANNEL
+#define MSKPHASE_6CHANNEL SNLED27351_SCAN_PHASE_6_CHANNEL
+#define MSKPHASE_5CHANNEL SNLED27351_SCAN_PHASE_5_CHANNEL
+#define MSKPHASE_4CHANNEL SNLED27351_SCAN_PHASE_4_CHANNEL
+#define MSKPHASE_3CHANNEL SNLED27351_SCAN_PHASE_3_CHANNEL
+#define MSKPHASE_2CHANNEL SNLED27351_SCAN_PHASE_2_CHANNEL
+#define MSKPHASE_1CHANNEL SNLED27351_SCAN_PHASE_1_CHANNEL
#define ckled2001_led snled27351_led_t
#define g_ckled2001_leds g_snled27351_leds
// ========
+#define SNLED27351_REG_COMMAND 0xFD
+#define SNLED27351_COMMAND_LED_CONTROL 0x00
+#define SNLED27351_COMMAND_PWM 0x01
+#define SNLED27351_COMMAND_FUNCTION 0x03
+#define SNLED27351_COMMAND_CURRENT_TUNE 0x04
+
+#define SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN 0x00
+#define SNLED27351_SOFTWARE_SHUTDOWN_SSD_SHUTDOWN (0x0 << 0)
+#define SNLED27351_SOFTWARE_SHUTDOWN_SSD_NORMAL (0x1 << 0)
+
+#define SNLED27351_FUNCTION_REG_ID 0x11
+#define SNLED27351_DRIVER_ID 0x8A
+
+#define SNLED27351_FUNCTION_REG_PULLDOWNUP 0x13
+#define SNLED27351_PULLDOWNUP_ALL_ENABLED 0xAA
+
+#define SNLED27351_FUNCTION_REG_SCAN_PHASE 0x14
+#define SNLED27351_SCAN_PHASE_12_CHANNEL 0x00
+#define SNLED27351_SCAN_PHASE_11_CHANNEL 0x01
+#define SNLED27351_SCAN_PHASE_10_CHANNEL 0x02
+#define SNLED27351_SCAN_PHASE_9_CHANNEL 0x03
+#define SNLED27351_SCAN_PHASE_8_CHANNEL 0x04
+#define SNLED27351_SCAN_PHASE_7_CHANNEL 0x05
+#define SNLED27351_SCAN_PHASE_6_CHANNEL 0x06
+#define SNLED27351_SCAN_PHASE_5_CHANNEL 0x07
+#define SNLED27351_SCAN_PHASE_4_CHANNEL 0x08
+#define SNLED27351_SCAN_PHASE_3_CHANNEL 0x09
+#define SNLED27351_SCAN_PHASE_2_CHANNEL 0x0A
+#define SNLED27351_SCAN_PHASE_1_CHANNEL 0x0B
+
+#define SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_1 0x15
+#define SNLED27351_SLEW_RATE_CONTROL_MODE_1_PDP_ENABLE (0b1 << 2)
+
+#define SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_2 0x16
+#define SNLED27351_SLEW_RATE_CONTROL_MODE_2_SSL_ENABLE (0b1 << 6)
+#define SNLED27351_SLEW_RATE_CONTROL_MODE_2_DSL_ENABLE (0b1 << 7)
+
+#define SNLED27351_FUNCTION_REG_OPEN_SHORT_ENABLE 0x17
+#define SNLED27351_OPEN_SHORT_ENABLE_SDS_ENABLE (0b1 << 6)
+#define SNLED27351_OPEN_SHORT_ENABLE_ODS_ENABLE (0b1 << 7)
+
+#define SNLED27351_FUNCTION_REG_OPEN_SHORT_DUTY 0x18
+
+#define SNLED27351_FUNCTION_REG_OPEN_SHORT_FLAG 0x19
+#define SNLED27351_OPEN_SHORT_FLAG_OSINT_ENABLE (0b1 << 6)
+#define SNLED27351_OPEN_SHORT_FLAG_ODINT_ENABLE (0b1 << 7)
+
+#define SNLED27351_FUNCTION_REG_SOFTWARE_SLEEP 0x1A
+#define SNLED27351_SOFTWARE_SLEEP_ENABLE (0b1 << 1)
+
+// LED Control Registers
+#define SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR 0x0
+#define SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR 0x17
+#define SNLED27351_LED_CONTROL_ON_OFF_LENGTH ((SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR - SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR) + 1)
+
+#define SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR 0x18
+#define SNLED27351_LED_CONTROL_OPEN_LAST_ADDR 0x2F
+#define SNLED27351_LED_CONTROL_OPEN_LENGTH ((SNLED27351_LED_CONTROL_OPEN_LAST_ADDR - SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR) + 1)
+
+#define SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR 0x30
+#define SNLED27351_LED_CONTROL_SHORT_LAST_ADDR 0x47
+#define SNLED27351_LED_CONTROL_SHORT_LENGTH ((SNLED27351_LED_CONTROL_SHORT_LAST_ADDR - SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR) + 1)
+
+#define SNLED27351_LED_CONTROL_PAGE_LENGTH 0x48
+
+// LED Control Registers
+#define SNLED27351_LED_PWM_FIRST_ADDR 0x00
+#define SNLED27351_LED_PWM_LAST_ADDR 0xBF
+#define SNLED27351_LED_PWM_LENGTH 0xC0
+
+// Current Tune Registers
+#define SNLED27351_LED_CURRENT_TUNE_FIRST_ADDR 0x00
+#define SNLED27351_LED_CURRENT_TUNE_LAST_ADDR 0x0B
+#define SNLED27351_LED_CURRENT_TUNE_LENGTH 0x0C
+
#define SNLED27351_I2C_ADDRESS_GND 0x74
#define SNLED27351_I2C_ADDRESS_SCL 0x75
#define SNLED27351_I2C_ADDRESS_SDA 0x76
@@ 100,92 175,6 @@ void snled27351_flush(void);
void snled27351_sw_return_normal(uint8_t addr);
void snled27351_sw_shutdown(uint8_t addr);
-// Registers Page Define
-#define SNLED27351_REG_CONFIGURE_CMD_PAGE 0xFD
-#define SNLED27351_LED_CONTROL_PAGE 0x00
-#define SNLED27351_LED_PWM_PAGE 0x01
-#define SNLED27351_FUNCTION_PAGE 0x03
-#define SNLED27351_CURRENT_TUNE_PAGE 0x04
-
-// Function Register: address 0x00
-#define SNLED27351_REG_CONFIGURATION 0x00
-#define SNLED27351_MSKSW_SHUT_DOWN_MODE (0x0 << 0)
-#define SNLED27351_MSKSW_NORMAL_MODE (0x1 << 0)
-
-#define SNLED27351_REG_DRIVER_ID 0x11
-#define SNLED27351_DRIVER_ID 0x8A
-
-#define SNLED27351_REG_PDU 0x13
-#define SNLED27351_MSKSET_CA_CB_CHANNEL 0xAA
-#define SNLED27351_MSKCLR_CA_CB_CHANNEL 0x00
-
-#define SNLED27351_REG_SCAN_PHASE 0x14
-#define SNLED27351_MSKPHASE_12CHANNEL 0x00
-#define SNLED27351_MSKPHASE_11CHANNEL 0x01
-#define SNLED27351_MSKPHASE_10CHANNEL 0x02
-#define SNLED27351_MSKPHASE_9CHANNEL 0x03
-#define SNLED27351_MSKPHASE_8CHANNEL 0x04
-#define SNLED27351_MSKPHASE_7CHANNEL 0x05
-#define SNLED27351_MSKPHASE_6CHANNEL 0x06
-#define SNLED27351_MSKPHASE_5CHANNEL 0x07
-#define SNLED27351_MSKPHASE_4CHANNEL 0x08
-#define SNLED27351_MSKPHASE_3CHANNEL 0x09
-#define SNLED27351_MSKPHASE_2CHANNEL 0x0A
-#define SNLED27351_MSKPHASE_1CHANNEL 0x0B
-
-#define SNLED27351_REG_SLEW_RATE_CONTROL_MODE1 0x15
-#define SNLED27351_MSKPWM_DELAY_PHASE_ENABLE 0x04
-#define SNLED27351_MSKPWM_DELAY_PHASE_DISABLE 0x00
-
-#define SNLED27351_REG_SLEW_RATE_CONTROL_MODE2 0x16
-#define SNLED27351_MSKDRIVING_SINKING_CHANNEL_SLEWRATE_ENABLE 0xC0
-#define SNLED27351_MSKDRIVING_SINKING_CHANNEL_SLEWRATE_DISABLE 0x00
-
-#define SNLED27351_REG_OPEN_SHORT_ENABLE 0x17
-#define SNLED27351_MSKOPEN_DETECTION_ENABLE (0x01 << 7)
-#define SNLED27351_MSKOPEN_DETECTION_DISABLE (0x00)
-
-#define SNLED27351_MSKSHORT_DETECTION_ENABLE (0x01 << 6)
-#define SNLED27351_MSKSHORT_DETECTION_DISABLE (0x00)
-
-#define SNLED27351_REG_OPEN_SHORT_DUTY 0x18
-#define SNLED27351_REG_OPEN_SHORT_FLAG 0x19
-
-#define SNLED27351_MSKOPEN_DETECTION_INTERRUPT_ENABLE (0x01 << 7)
-#define SNLED27351_MSKOPEN_DETECTION_INTERRUPT_DISABLE (0x00)
-
-#define SNLED27351_MSKSHORT_DETECTION_INTERRUPT_ENABLE (0x01 << 6)
-#define SNLED27351_MSKSHORT_DETECTION_INTERRUPT_DISABLE (0x00)
-
-#define SNLED27351_REG_SOFTWARE_SLEEP 0x1A
-#define SNLED27351_MSKSLEEP_ENABLE 0x02
-#define SNLED27351_MSKSLEEP_DISABLE 0x00
-
-// LED Control Registers
-#define SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR 0x0
-#define SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR 0x17
-#define SNLED27351_LED_CONTROL_ON_OFF_LENGTH ((SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR - SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR) + 1)
-
-#define SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR 0x18
-#define SNLED27351_LED_CONTROL_OPEN_LAST_ADDR 0x2F
-#define SNLED27351_LED_CONTROL_OPEN_LENGTH ((SNLED27351_LED_CONTROL_OPEN_LAST_ADDR - SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR) + 1)
-
-#define SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR 0x30
-#define SNLED27351_LED_CONTROL_SHORT_LAST_ADDR 0x47
-#define SNLED27351_LED_CONTROL_SHORT_LENGTH ((SNLED27351_LED_CONTROL_SHORT_LAST_ADDR - SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR) + 1)
-
-#define SNLED27351_LED_CONTROL_PAGE_LENGTH 0x48
-
-// LED Control Registers
-#define SNLED27351_LED_PWM_FIRST_ADDR 0x00
-#define SNLED27351_LED_PWM_LAST_ADDR 0xBF
-#define SNLED27351_LED_PWM_LENGTH 0xC0
-
-// Current Tune Registers
-#define SNLED27351_LED_CURRENT_TUNE_FIRST_ADDR 0x00
-#define SNLED27351_LED_CURRENT_TUNE_LAST_ADDR 0x0B
-#define SNLED27351_LED_CURRENT_TUNE_LENGTH 0x0C
-
#define A_1 0x00
#define A_2 0x01
#define A_3 0x02
M drivers/led/snled27351.c => drivers/led/snled27351.c +21 -21
@@ 29,7 29,7 @@
#endif
#ifndef SNLED27351_PHASE_CHANNEL
-# define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_12CHANNEL
+# define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_12_CHANNEL
#endif
#ifndef SNLED27351_CURRENT_TUNE
@@ 133,48 133,48 @@ void snled27351_init_drivers(void) {
void snled27351_init(uint8_t addr) {
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to shutdown mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_SHUT_DOWN_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_SHUTDOWN);
// Setting internal channel pulldown/pullup
- snled27351_write_register(addr, SNLED27351_REG_PDU, SNLED27351_MSKSET_CA_CB_CHANNEL);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_PULLDOWNUP, SNLED27351_PULLDOWNUP_ALL_ENABLED);
// Select number of scan phase
- snled27351_write_register(addr, SNLED27351_REG_SCAN_PHASE, SNLED27351_PHASE_CHANNEL);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SCAN_PHASE, SNLED27351_PHASE_CHANNEL);
// Setting PWM Delay Phase
- snled27351_write_register(addr, SNLED27351_REG_SLEW_RATE_CONTROL_MODE1, SNLED27351_MSKPWM_DELAY_PHASE_ENABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_1, SNLED27351_SLEW_RATE_CONTROL_MODE_1_PDP_ENABLE);
// Setting Driving/Sinking Channel Slew Rate
- snled27351_write_register(addr, SNLED27351_REG_SLEW_RATE_CONTROL_MODE2, SNLED27351_MSKDRIVING_SINKING_CHANNEL_SLEWRATE_ENABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_2, SNLED27351_SLEW_RATE_CONTROL_MODE_2_DSL_ENABLE | SNLED27351_SLEW_RATE_CONTROL_MODE_2_SSL_ENABLE);
// Setting Iref
- snled27351_write_register(addr, SNLED27351_REG_SOFTWARE_SLEEP, SNLED27351_MSKSLEEP_DISABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SLEEP, 0);
// Set LED CONTROL PAGE (Page 0)
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_CONTROL_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_LED_CONTROL);
for (int i = 0; i < SNLED27351_LED_CONTROL_ON_OFF_LENGTH; i++) {
snled27351_write_register(addr, i, 0x00);
}
// Set PWM PAGE (Page 1)
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_PWM_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_PWM);
for (int i = 0; i < SNLED27351_LED_CURRENT_TUNE_LENGTH; i++) {
snled27351_write_register(addr, i, 0x00);
}
// Set CURRENT PAGE (Page 4)
uint8_t current_tune_reg_list[SNLED27351_LED_CURRENT_TUNE_LENGTH] = SNLED27351_CURRENT_TUNE;
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_CURRENT_TUNE_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_CURRENT_TUNE);
for (int i = 0; i < SNLED27351_LED_CURRENT_TUNE_LENGTH; i++) {
snled27351_write_register(addr, i, current_tune_reg_list[i]);
}
// Enable LEDs ON/OFF
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_CONTROL_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_LED_CONTROL);
for (int i = 0; i < SNLED27351_LED_CONTROL_ON_OFF_LENGTH; i++) {
snled27351_write_register(addr, i, 0xFF);
}
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to normal mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_NORMAL_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_NORMAL);
}
void snled27351_set_color(int index, uint8_t red, uint8_t green, uint8_t blue) {
@@ 230,7 230,7 @@ void snled27351_set_led_control_register(uint8_t index, bool red, bool green, bo
void snled27351_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_PWM_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_PWM);
// If any of the transactions fail we risk writing dirty PG0,
// refresh page 0 just in case.
@@ 243,7 243,7 @@ void snled27351_update_pwm_buffers(uint8_t addr, uint8_t index) {
void snled27351_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_LED_CONTROL_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_LED_CONTROL);
for (int i = 0; i < SNLED27351_LED_CONTROL_REGISTER_COUNT; i++) {
snled27351_write_register(addr, i, g_led_control_registers[index][i]);
}
@@ 266,16 266,16 @@ void snled27351_flush(void) {
void snled27351_sw_return_normal(uint8_t addr) {
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to normal mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_NORMAL_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_NORMAL);
}
void snled27351_sw_shutdown(uint8_t addr) {
// Select to function page
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURE_CMD_PAGE, SNLED27351_FUNCTION_PAGE);
+ snled27351_write_register(addr, SNLED27351_REG_COMMAND, SNLED27351_COMMAND_FUNCTION);
// Setting LED driver to shutdown mode
- snled27351_write_register(addr, SNLED27351_REG_CONFIGURATION, SNLED27351_MSKSW_SHUT_DOWN_MODE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN, SNLED27351_SOFTWARE_SHUTDOWN_SSD_SHUTDOWN);
// Write SW Sleep Register
- snled27351_write_register(addr, SNLED27351_REG_SOFTWARE_SLEEP, SNLED27351_MSKSLEEP_ENABLE);
+ snled27351_write_register(addr, SNLED27351_FUNCTION_REG_SOFTWARE_SLEEP, SNLED27351_SOFTWARE_SLEEP_ENABLE);
}
M drivers/led/snled27351.h => drivers/led/snled27351.h +87 -98
@@ 47,23 47,98 @@
# define SNLED27351_CURRENT_TUNE CKLED2001_CURRENT_TUNE
#endif
-#define MSKPHASE_12CHANNEL SNLED27351_MSKPHASE_12CHANNEL
-#define MSKPHASE_11CHANNEL SNLED27351_MSKPHASE_11CHANNEL
-#define MSKPHASE_10CHANNEL SNLED27351_MSKPHASE_10CHANNEL
-#define MSKPHASE_9CHANNEL SNLED27351_MSKPHASE_9CHANNEL
-#define MSKPHASE_8CHANNEL SNLED27351_MSKPHASE_8CHANNEL
-#define MSKPHASE_7CHANNEL SNLED27351_MSKPHASE_7CHANNEL
-#define MSKPHASE_6CHANNEL SNLED27351_MSKPHASE_6CHANNEL
-#define MSKPHASE_5CHANNEL SNLED27351_MSKPHASE_5CHANNEL
-#define MSKPHASE_4CHANNEL SNLED27351_MSKPHASE_4CHANNEL
-#define MSKPHASE_3CHANNEL SNLED27351_MSKPHASE_3CHANNEL
-#define MSKPHASE_2CHANNEL SNLED27351_MSKPHASE_2CHANNEL
-#define MSKPHASE_1CHANNEL SNLED27351_MSKPHASE_1CHANNEL
+#define MSKPHASE_12CHANNEL SNLED27351_SCAN_PHASE_12_CHANNEL
+#define MSKPHASE_11CHANNEL SNLED27351_SCAN_PHASE_11_CHANNEL
+#define MSKPHASE_10CHANNEL SNLED27351_SCAN_PHASE_10_CHANNEL
+#define MSKPHASE_9CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
+#define MSKPHASE_8CHANNEL SNLED27351_SCAN_PHASE_8_CHANNEL
+#define MSKPHASE_7CHANNEL SNLED27351_SCAN_PHASE_7_CHANNEL
+#define MSKPHASE_6CHANNEL SNLED27351_SCAN_PHASE_6_CHANNEL
+#define MSKPHASE_5CHANNEL SNLED27351_SCAN_PHASE_5_CHANNEL
+#define MSKPHASE_4CHANNEL SNLED27351_SCAN_PHASE_4_CHANNEL
+#define MSKPHASE_3CHANNEL SNLED27351_SCAN_PHASE_3_CHANNEL
+#define MSKPHASE_2CHANNEL SNLED27351_SCAN_PHASE_2_CHANNEL
+#define MSKPHASE_1CHANNEL SNLED27351_SCAN_PHASE_1_CHANNEL
#define ckled2001_led snled27351_led_t
#define g_ckled2001_leds g_snled27351_leds
// ========
+#define SNLED27351_REG_COMMAND 0xFD
+#define SNLED27351_COMMAND_LED_CONTROL 0x00
+#define SNLED27351_COMMAND_PWM 0x01
+#define SNLED27351_COMMAND_FUNCTION 0x03
+#define SNLED27351_COMMAND_CURRENT_TUNE 0x04
+
+#define SNLED27351_FUNCTION_REG_SOFTWARE_SHUTDOWN 0x00
+#define SNLED27351_SOFTWARE_SHUTDOWN_SSD_SHUTDOWN (0x0 << 0)
+#define SNLED27351_SOFTWARE_SHUTDOWN_SSD_NORMAL (0x1 << 0)
+
+#define SNLED27351_FUNCTION_REG_ID 0x11
+#define SNLED27351_DRIVER_ID 0x8A
+
+#define SNLED27351_FUNCTION_REG_PULLDOWNUP 0x13
+#define SNLED27351_PULLDOWNUP_ALL_ENABLED 0xAA
+
+#define SNLED27351_FUNCTION_REG_SCAN_PHASE 0x14
+#define SNLED27351_SCAN_PHASE_12_CHANNEL 0x00
+#define SNLED27351_SCAN_PHASE_11_CHANNEL 0x01
+#define SNLED27351_SCAN_PHASE_10_CHANNEL 0x02
+#define SNLED27351_SCAN_PHASE_9_CHANNEL 0x03
+#define SNLED27351_SCAN_PHASE_8_CHANNEL 0x04
+#define SNLED27351_SCAN_PHASE_7_CHANNEL 0x05
+#define SNLED27351_SCAN_PHASE_6_CHANNEL 0x06
+#define SNLED27351_SCAN_PHASE_5_CHANNEL 0x07
+#define SNLED27351_SCAN_PHASE_4_CHANNEL 0x08
+#define SNLED27351_SCAN_PHASE_3_CHANNEL 0x09
+#define SNLED27351_SCAN_PHASE_2_CHANNEL 0x0A
+#define SNLED27351_SCAN_PHASE_1_CHANNEL 0x0B
+
+#define SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_1 0x15
+#define SNLED27351_SLEW_RATE_CONTROL_MODE_1_PDP_ENABLE (0b1 << 2)
+
+#define SNLED27351_FUNCTION_REG_SLEW_RATE_CONTROL_MODE_2 0x16
+#define SNLED27351_SLEW_RATE_CONTROL_MODE_2_SSL_ENABLE (0b1 << 6)
+#define SNLED27351_SLEW_RATE_CONTROL_MODE_2_DSL_ENABLE (0b1 << 7)
+
+#define SNLED27351_FUNCTION_REG_OPEN_SHORT_ENABLE 0x17
+#define SNLED27351_OPEN_SHORT_ENABLE_SDS_ENABLE (0b1 << 6)
+#define SNLED27351_OPEN_SHORT_ENABLE_ODS_ENABLE (0b1 << 7)
+
+#define SNLED27351_FUNCTION_REG_OPEN_SHORT_DUTY 0x18
+
+#define SNLED27351_FUNCTION_REG_OPEN_SHORT_FLAG 0x19
+#define SNLED27351_OPEN_SHORT_FLAG_OSINT_ENABLE (0b1 << 6)
+#define SNLED27351_OPEN_SHORT_FLAG_ODINT_ENABLE (0b1 << 7)
+
+#define SNLED27351_FUNCTION_REG_SOFTWARE_SLEEP 0x1A
+#define SNLED27351_SOFTWARE_SLEEP_ENABLE (0b1 << 1)
+
+// LED Control Registers
+#define SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR 0x0
+#define SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR 0x17
+#define SNLED27351_LED_CONTROL_ON_OFF_LENGTH ((SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR - SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR) + 1)
+
+#define SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR 0x18
+#define SNLED27351_LED_CONTROL_OPEN_LAST_ADDR 0x2F
+#define SNLED27351_LED_CONTROL_OPEN_LENGTH ((SNLED27351_LED_CONTROL_OPEN_LAST_ADDR - SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR) + 1)
+
+#define SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR 0x30
+#define SNLED27351_LED_CONTROL_SHORT_LAST_ADDR 0x47
+#define SNLED27351_LED_CONTROL_SHORT_LENGTH ((SNLED27351_LED_CONTROL_SHORT_LAST_ADDR - SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR) + 1)
+
+#define SNLED27351_LED_CONTROL_PAGE_LENGTH 0x48
+
+// LED Control Registers
+#define SNLED27351_LED_PWM_FIRST_ADDR 0x00
+#define SNLED27351_LED_PWM_LAST_ADDR 0xBF
+#define SNLED27351_LED_PWM_LENGTH 0xC0
+
+// Current Tune Registers
+#define SNLED27351_LED_CURRENT_TUNE_FIRST_ADDR 0x00
+#define SNLED27351_LED_CURRENT_TUNE_LAST_ADDR 0x0B
+#define SNLED27351_LED_CURRENT_TUNE_LENGTH 0x0C
+
#define SNLED27351_I2C_ADDRESS_GND 0x74
#define SNLED27351_I2C_ADDRESS_SCL 0x75
#define SNLED27351_I2C_ADDRESS_SDA 0x76
@@ 114,92 189,6 @@ void snled27351_flush(void);
void snled27351_sw_return_normal(uint8_t addr);
void snled27351_sw_shutdown(uint8_t addr);
-// Registers Page Define
-#define SNLED27351_REG_CONFIGURE_CMD_PAGE 0xFD
-#define SNLED27351_LED_CONTROL_PAGE 0x00
-#define SNLED27351_LED_PWM_PAGE 0x01
-#define SNLED27351_FUNCTION_PAGE 0x03
-#define SNLED27351_CURRENT_TUNE_PAGE 0x04
-
-// Function Register: address 0x00
-#define SNLED27351_REG_CONFIGURATION 0x00
-#define SNLED27351_MSKSW_SHUT_DOWN_MODE (0x0 << 0)
-#define SNLED27351_MSKSW_NORMAL_MODE (0x1 << 0)
-
-#define SNLED27351_REG_DRIVER_ID 0x11
-#define SNLED27351_DRIVER_ID 0x8A
-
-#define SNLED27351_REG_PDU 0x13
-#define SNLED27351_MSKSET_CA_CB_CHANNEL 0xAA
-#define SNLED27351_MSKCLR_CA_CB_CHANNEL 0x00
-
-#define SNLED27351_REG_SCAN_PHASE 0x14
-#define SNLED27351_MSKPHASE_12CHANNEL 0x00
-#define SNLED27351_MSKPHASE_11CHANNEL 0x01
-#define SNLED27351_MSKPHASE_10CHANNEL 0x02
-#define SNLED27351_MSKPHASE_9CHANNEL 0x03
-#define SNLED27351_MSKPHASE_8CHANNEL 0x04
-#define SNLED27351_MSKPHASE_7CHANNEL 0x05
-#define SNLED27351_MSKPHASE_6CHANNEL 0x06
-#define SNLED27351_MSKPHASE_5CHANNEL 0x07
-#define SNLED27351_MSKPHASE_4CHANNEL 0x08
-#define SNLED27351_MSKPHASE_3CHANNEL 0x09
-#define SNLED27351_MSKPHASE_2CHANNEL 0x0A
-#define SNLED27351_MSKPHASE_1CHANNEL 0x0B
-
-#define SNLED27351_REG_SLEW_RATE_CONTROL_MODE1 0x15
-#define SNLED27351_MSKPWM_DELAY_PHASE_ENABLE 0x04
-#define SNLED27351_MSKPWM_DELAY_PHASE_DISABLE 0x00
-
-#define SNLED27351_REG_SLEW_RATE_CONTROL_MODE2 0x16
-#define SNLED27351_MSKDRIVING_SINKING_CHANNEL_SLEWRATE_ENABLE 0xC0
-#define SNLED27351_MSKDRIVING_SINKING_CHANNEL_SLEWRATE_DISABLE 0x00
-
-#define SNLED27351_REG_OPEN_SHORT_ENABLE 0x17
-#define SNLED27351_MSKOPEN_DETECTION_ENABLE (0x01 << 7)
-#define SNLED27351_MSKOPEN_DETECTION_DISABLE (0x00)
-
-#define SNLED27351_MSKSHORT_DETECTION_ENABLE (0x01 << 6)
-#define SNLED27351_MSKSHORT_DETECTION_DISABLE (0x00)
-
-#define SNLED27351_REG_OPEN_SHORT_DUTY 0x18
-#define SNLED27351_REG_OPEN_SHORT_FLAG 0x19
-
-#define SNLED27351_MSKOPEN_DETECTION_INTERRUPT_ENABLE (0x01 << 7)
-#define SNLED27351_MSKOPEN_DETECTION_INTERRUPT_DISABLE (0x00)
-
-#define SNLED27351_MSKSHORT_DETECTION_INTERRUPT_ENABLE (0x01 << 6)
-#define SNLED27351_MSKSHORT_DETECTION_INTERRUPT_DISABLE (0x00)
-
-#define SNLED27351_REG_SOFTWARE_SLEEP 0x1A
-#define SNLED27351_MSKSLEEP_ENABLE 0x02
-#define SNLED27351_MSKSLEEP_DISABLE 0x00
-
-// LED Control Registers
-#define SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR 0x0
-#define SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR 0x17
-#define SNLED27351_LED_CONTROL_ON_OFF_LENGTH ((SNLED27351_LED_CONTROL_ON_OFF_LAST_ADDR - SNLED27351_LED_CONTROL_ON_OFF_FIRST_ADDR) + 1)
-
-#define SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR 0x18
-#define SNLED27351_LED_CONTROL_OPEN_LAST_ADDR 0x2F
-#define SNLED27351_LED_CONTROL_OPEN_LENGTH ((SNLED27351_LED_CONTROL_OPEN_LAST_ADDR - SNLED27351_LED_CONTROL_OPEN_FIRST_ADDR) + 1)
-
-#define SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR 0x30
-#define SNLED27351_LED_CONTROL_SHORT_LAST_ADDR 0x47
-#define SNLED27351_LED_CONTROL_SHORT_LENGTH ((SNLED27351_LED_CONTROL_SHORT_LAST_ADDR - SNLED27351_LED_CONTROL_SHORT_FIRST_ADDR) + 1)
-
-#define SNLED27351_LED_CONTROL_PAGE_LENGTH 0x48
-
-// LED Control Registers
-#define SNLED27351_LED_PWM_FIRST_ADDR 0x00
-#define SNLED27351_LED_PWM_LAST_ADDR 0xBF
-#define SNLED27351_LED_PWM_LENGTH 0xC0
-
-// Current Tune Registers
-#define SNLED27351_LED_CURRENT_TUNE_FIRST_ADDR 0x00
-#define SNLED27351_LED_CURRENT_TUNE_LAST_ADDR 0x0B
-#define SNLED27351_LED_CURRENT_TUNE_LENGTH 0x0C
-
#define A_1 0x00
#define A_2 0x01
#define A_3 0x02
M keyboards/input_club/k_type/is31fl3733-dual.c => keyboards/input_club/k_type/is31fl3733-dual.c +16 -32
@@ 20,22 20,6 @@
#include "i2c_master.h"
#include "wait.h"
-#define IS31FL3733_COMMANDREGISTER 0xFD
-#define IS31FL3733_COMMANDREGISTER_WRITELOCK 0xFE
-#define IS31FL3733_INTERRUPTMASKREGISTER 0xF0
-#define IS31FL3733_INTERRUPTSTATUSREGISTER 0xF1
-
-#define IS31FL3733_PAGE_LEDCONTROL 0x00 // PG0
-#define IS31FL3733_PAGE_PWM 0x01 // PG1
-#define IS31FL3733_PAGE_AUTOBREATH 0x02 // PG2
-#define IS31FL3733_PAGE_FUNCTION 0x03 // PG3
-
-#define IS31FL3733_REG_CONFIGURATION 0x00 // PG3
-#define IS31FL3733_REG_GLOBALCURRENT 0x01 // PG3
-#define IS31FL3733_REG_RESET 0x11 // PG3
-#define IS31FL3733_REG_SW_PULLUP 0x0F // PG3
-#define IS31FL3733_REG_CS_PULLDOWN 0x10 // PG3
-
#define IS31FL3733_PWM_REGISTER_COUNT 192
#define IS31FL3733_LED_CONTROL_REGISTER_COUNT 24
@@ 59,8 43,8 @@
# define IS31FL3733_CS_PULLDOWN IS31FL3733_PDR_0_OHM
#endif
-#ifndef IS31FL3733_GLOBALCURRENT
-# define IS31FL3733_GLOBALCURRENT 0xFF
+#ifndef IS31FL3733_GLOBAL_CURRENT
+# define IS31FL3733_GLOBAL_CURRENT 0xFF
#endif
#ifndef IS31FL3733_SYNC_1
@@ 167,20 151,20 @@ void is31fl3733_init(uint8_t bus, uint8_t addr, uint8_t sync) {
// Sync is passed so set it according to the datasheet.
// Unlock the command register.
- is31fl3733_write_register(bus, addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(bus, addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG0
- is31fl3733_write_register(bus, addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_LEDCONTROL);
+ is31fl3733_write_register(bus, addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_LED_CONTROL);
// Turn off all LEDs.
for (int i = 0; i < IS31FL3733_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3733_write_register(bus, addr, i, 0x00);
}
// Unlock the command register.
- is31fl3733_write_register(bus, addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(bus, addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG1
- is31fl3733_write_register(bus, addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_PWM);
+ is31fl3733_write_register(bus, addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_PWM);
// Set PWM on all LEDs to 0
// No need to setup Breath registers to PWM as that is the default.
for (int i = 0; i < IS31FL3733_PWM_REGISTER_COUNT; i++) {
@@ 188,18 172,18 @@ void is31fl3733_init(uint8_t bus, uint8_t addr, uint8_t sync) {
}
// Unlock the command register.
- is31fl3733_write_register(bus, addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
+ is31fl3733_write_register(bus, addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
// Select PG3
- is31fl3733_write_register(bus, addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_FUNCTION);
+ is31fl3733_write_register(bus, addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_FUNCTION);
// Set de-ghost pull-up resistors (SWx)
- is31fl3733_write_register(bus, addr, IS31FL3733_REG_SW_PULLUP, IS31FL3733_SW_PULLUP);
+ is31fl3733_write_register(bus, addr, IS31FL3733_FUNCTION_REG_SW_PULLUP, IS31FL3733_SW_PULLUP);
// Set de-ghost pull-down resistors (CSx)
- is31fl3733_write_register(bus, addr, IS31FL3733_REG_CS_PULLDOWN, IS31FL3733_CS_PULLDOWN);
+ is31fl3733_write_register(bus, addr, IS31FL3733_FUNCTION_REG_CS_PULLDOWN, IS31FL3733_CS_PULLDOWN);
// Set global current to maximum.
- is31fl3733_write_register(bus, addr, IS31FL3733_REG_GLOBALCURRENT, IS31FL3733_GLOBALCURRENT);
+ is31fl3733_write_register(bus, addr, IS31FL3733_FUNCTION_REG_GLOBAL_CURRENT, IS31FL3733_GLOBAL_CURRENT);
// Disable software shutdown.
- is31fl3733_write_register(bus, addr, IS31FL3733_REG_CONFIGURATION, ((sync & 0b11) << 6) | ((IS31FL3733_PWM_FREQUENCY & 0b111) << 3) | 0x01);
+ is31fl3733_write_register(bus, addr, IS31FL3733_FUNCTION_REG_CONFIGURATION, ((sync & 0b11) << 6) | ((IS31FL3733_PWM_FREQUENCY & 0b111) << 3) | 0x01);
// Wait 10ms to ensure the device has woken up.
wait_ms(10);
@@ 259,8 243,8 @@ void is31fl3733_set_led_control_register(uint8_t index, bool red, bool green, bo
void is31fl3733_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required[index]) {
// Firstly we need to unlock the command register and select PG1.
- is31fl3733_write_register(index, addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3733_write_register(index, addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_PWM);
+ is31fl3733_write_register(index, addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3733_write_register(index, addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_PWM);
// If any of the transactions fail we risk writing dirty PG0,
// refresh page 0 just in case.
@@ 274,8 258,8 @@ void is31fl3733_update_pwm_buffers(uint8_t addr, uint8_t index) {
void is31fl3733_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required[index]) {
// Firstly we need to unlock the command register and select PG0
- is31fl3733_write_register(index, addr, IS31FL3733_COMMANDREGISTER_WRITELOCK, 0xC5);
- is31fl3733_write_register(index, addr, IS31FL3733_COMMANDREGISTER, IS31FL3733_PAGE_LEDCONTROL);
+ is31fl3733_write_register(index, addr, IS31FL3733_REG_COMMAND_WRITE_LOCK, IS31FL3733_COMMAND_WRITE_LOCK_MAGIC);
+ is31fl3733_write_register(index, addr, IS31FL3733_REG_COMMAND, IS31FL3733_COMMAND_LED_CONTROL);
for (int i = 0; i < IS31FL3733_LED_CONTROL_REGISTER_COUNT; i++) {
is31fl3733_write_register(index, addr, i, g_led_control_registers[index][i]);
}
M keyboards/input_club/k_type/is31fl3733-dual.h => keyboards/input_club/k_type/is31fl3733-dual.h +19 -0
@@ 22,6 22,25 @@
#include <stdbool.h>
#include "progmem.h"
+#define IS31FL3733_REG_INTERRUPT_MASK 0xF0
+#define IS31FL3733_REG_INTERRUPT_STATUS 0xF1
+
+#define IS31FL3733_REG_COMMAND 0xFD
+
+#define IS31FL3733_COMMAND_LED_CONTROL 0x00
+#define IS31FL3733_COMMAND_PWM 0x01
+#define IS31FL3733_COMMAND_AUTO_BREATH 0x02
+#define IS31FL3733_COMMAND_FUNCTION 0x03
+
+#define IS31FL3733_FUNCTION_REG_CONFIGURATION 0x00
+#define IS31FL3733_FUNCTION_REG_GLOBAL_CURRENT 0x01
+#define IS31FL3733_FUNCTION_REG_SW_PULLUP 0x0F
+#define IS31FL3733_FUNCTION_REG_CS_PULLDOWN 0x10
+#define IS31FL3733_FUNCTION_REG_RESET 0x11
+
+#define IS31FL3733_REG_COMMAND_WRITE_LOCK 0xFE
+#define IS31FL3733_COMMAND_WRITE_LOCK_MAGIC 0xC5
+
#define IS31FL3733_I2C_ADDRESS_GND_GND 0x50
#define IS31FL3733_I2C_ADDRESS_GND_SCL 0x51
#define IS31FL3733_I2C_ADDRESS_GND_SDA 0x52
M keyboards/keychron/c1_pro/ansi/rgb/config.h => keyboards/keychron/c1_pro/ansi/rgb/config.h +1 -1
@@ 29,7 29,7 @@
#define DRIVER_2_LED_TOTAL 39
#define RGB_MATRIX_LED_COUNT (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* Set led driver current */
#define SNLED27351_CURRENT_TUNE \
{ 0x9D, 0x9D, 0x44, 0x9D, 0x9D, 0x44, 0x9D, 0x9D, 0x44, 0x9D, 0x9D, 0x44 }
M keyboards/keychron/c1_pro/ansi/white/config.h => keyboards/keychron/c1_pro/ansi/white/config.h +1 -1
@@ 26,7 26,7 @@
/* LED Matrix Configuration */
#define LED_MATRIX_LED_COUNT 90
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* Set led driver current */
#define SNLED27351_CURRENT_TUNE \
{ 0x9D, 0x9D, 0x44, 0x9D, 0x9D, 0x44, 0x9D, 0x9D, 0x44, 0x9D, 0x9D, 0x44 }
M keyboards/keychron/q0/plus/config.h => keyboards/keychron/q0/plus/config.h +1 -1
@@ 23,7 23,7 @@
/* RGB Matrix Configuration */
#define RGB_MATRIX_LED_COUNT 26
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* Encoder Configuration*/
#define ENCODER_DEFAULT_POS 0x3
M keyboards/keychron/q10/config.h => keyboards/keychron/q10/config.h +1 -1
@@ 41,7 41,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE \
{ 0x98, 0x98, 0x4A, 0x98, 0x98, 0x4A, 0x98, 0x98, 0x4A, 0x98, 0x98, 0x4A }
M keyboards/keychron/q1v2/config.h => keyboards/keychron/q1v2/config.h +1 -1
@@ 44,7 44,7 @@
#define WEAR_LEVELING_LOGICAL_SIZE 2048
#define WEAR_LEVELING_BACKING_SIZE (WEAR_LEVELING_LOGICAL_SIZE * 2)
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* Set LED driver current */
#define SNLED27351_CURRENT_TUNE \
{ 0xA6, 0xA6, 0x50, 0xA6, 0xA6, 0x50, 0xA6, 0xA6, 0x50, 0xA6, 0xA6, 0x50 }
M keyboards/keychron/q2/config.h => keyboards/keychron/q2/config.h +1 -1
@@ 26,7 26,7 @@
#define SNLED27351_I2C_ADDRESS_1 SNLED27351_I2C_ADDRESS_VDDIO
#define SNLED27351_I2C_ADDRESS_2 SNLED27351_I2C_ADDRESS_GND
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* Disable DIP switch in matrix data */
#define MATRIX_MASKED
M keyboards/keychron/q3/config.h => keyboards/keychron/q3/config.h +1 -1
@@ 28,7 28,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* DIP switch */
#define DIP_SWITCH_MATRIX_GRID { {5, 4} }
M keyboards/keychron/q4/ansi/v1/config.h => keyboards/keychron/q4/ansi/v1/config.h +1 -2
@@ 24,5 24,4 @@
/* RGB Matrix Configuration */
#define RGB_MATRIX_LED_COUNT 61
-/* Scan phase of led driver set as SNLED27351_MSKPHASE_9CHANNEL(defined as 0x03 in SNLED27351.h) */
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
M keyboards/keychron/q65/config.h => keyboards/keychron/q65/config.h +1 -1
@@ 37,7 37,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 30U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE \
{ 0xB8, 0xB8, 0x58, 0xB8, 0xB8, 0x58, 0xB8, 0xB8, 0x58, 0xB8, 0xB8, 0x58 }
M keyboards/keychron/q7/config.h => keyboards/keychron/q7/config.h +1 -1
@@ 28,7 28,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE \
{ 0xF8, 0xF8, 0x80, 0xF8, 0xF8, 0x80, 0xF8, 0xF8, 0x80, 0xF8, 0xF8, 0x80 }
M keyboards/keychron/q8/config.h => keyboards/keychron/q8/config.h +1 -1
@@ 31,7 31,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE \
{ 0xC4, 0xC4, 0x60, 0xC4, 0xC4, 0x60, 0xC4, 0xC4, 0x60, 0xC4, 0xC4, 0x60 }
M keyboards/keychron/s1/ansi/rgb/config.h => keyboards/keychron/s1/ansi/rgb/config.h +1 -1
@@ 24,7 24,7 @@
#define DRIVER_2_LED_TOTAL 38
#define RGB_MATRIX_LED_COUNT (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE \
{ 0xA0, 0xA0, 0x48, 0xA0, 0xA0, 0x48, 0xA0, 0xA0, 0x48, 0xA0, 0xA0, 0x48 }
M keyboards/keychron/s1/ansi/white/config.h => keyboards/keychron/s1/ansi/white/config.h +1 -1
@@ 22,7 22,7 @@
#define DRIVER_1_LED_TOTAL 84
#define LED_MATRIX_LED_COUNT DRIVER_1_LED_TOTAL
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_6CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_6_CHANNEL
#define SNLED27351_CURRENT_TUNE \
{ 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80 } // 250mA
// { 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40 } // 127mA
M keyboards/keychron/v1/config.h => keyboards/keychron/v1/config.h +1 -1
@@ 43,7 43,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* turn off effects when suspended */
#define RGB_DISABLE_WHEN_USB_SUSPENDED
M keyboards/keychron/v10/config.h => keyboards/keychron/v10/config.h +1 -1
@@ 42,7 42,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE { 0x98, 0x98, 0x4A, 0x98, 0x98, 0x4A, 0x98, 0x98, 0x4A, 0x98, 0x98, 0x4A }
/* DIP switch */
M keyboards/keychron/v2/config.h => keyboards/keychron/v2/config.h +1 -1
@@ 31,7 31,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* Disable DIP switch in matrix data */
#define MATRIX_MASKED
M keyboards/keychron/v3/config.h => keyboards/keychron/v3/config.h +1 -1
@@ 31,7 31,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
/* DIP switch */
#define DIP_SWITCH_MATRIX_GRID { {5, 4} }
M keyboards/keychron/v7/config.h => keyboards/keychron/v7/config.h +1 -1
@@ 28,7 28,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE { 0xFC, 0xFC, 0x70, 0xFC, 0xFC, 0x70, 0xFC, 0xFC, 0x70, 0xFC, 0xFC, 0x70 }
/* DIP switch */
M keyboards/keychron/v8/config.h => keyboards/keychron/v8/config.h +1 -1
@@ 31,7 31,7 @@
#define I2C1_TIMINGR_SCLH 15U
#define I2C1_TIMINGR_SCLL 51U
-#define SNLED27351_PHASE_CHANNEL SNLED27351_MSKPHASE_9CHANNEL
+#define SNLED27351_PHASE_CHANNEL SNLED27351_SCAN_PHASE_9_CHANNEL
#define SNLED27351_CURRENT_TUNE { 0xC4, 0xC4, 0x60, 0xC4, 0xC4, 0x60, 0xC4, 0xC4, 0x60, 0xC4, 0xC4, 0x60 }
/* DIP switch */