M common_features.mk => common_features.mk +19 -1
@@ 114,8 114,26 @@ ifeq ($(strip $(RGBLIGHT_ENABLE)), yes)
endif
endif
-RGB_MATRIX_ENABLE ?= no
VALID_MATRIX_TYPES := yes IS31FL3731 IS31FL3733 custom
+
+LED_MATRIX_ENABLE ?= no
+ifneq ($(strip $(LED_MATRIX_ENABLE)), no)
+ifeq ($(filter $(LED_MATRIX_ENABLE),$(VALID_MATRIX_TYPES)),)
+ $(error LED_MATRIX_ENABLE="$(LED_MATRIX_ENABLE)" is not a valid matrix type)
+endif
+ OPT_DEFS += -DLED_MATRIX_ENABLE
+ SRC += $(QUANTUM_DIR)/led_matrix.c
+ SRC += $(QUANTUM_DIR)/led_matrix_drivers.c
+endif
+
+ifeq ($(strip $(LED_MATRIX_ENABLE)), IS31FL3731)
+ OPT_DEFS += -DIS31FL3731
+ COMMON_VPATH += $(DRIVER_PATH)/issi
+ SRC += is31fl3731-simple.c
+ SRC += i2c_master.c
+endif
+
+RGB_MATRIX_ENABLE ?= no
ifneq ($(strip $(RGB_MATRIX_ENABLE)), no)
ifeq ($(filter $(RGB_MATRIX_ENABLE),$(VALID_MATRIX_TYPES)),)
$(error RGB_MATRIX_ENABLE="$(RGB_MATRIX_ENABLE)" is not a valid matrix type)
A docs/feature_led_matrix.md => docs/feature_led_matrix.md +217 -0
@@ 0,0 1,217 @@
+# RGB Matrix Lighting
+
+## Driver configuration
+
+### IS31FL3731
+
+There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`:
+
+ LED_MATRIX_ENABLE = IS31FL3731
+
+Configure the hardware via your `config.h`:
+
+ // This is a 7-bit address, that gets left-shifted and bit 0
+ // set to 0 for write, 1 for read (as per I2C protocol)
+ // The address will vary depending on your wiring:
+ // 0b1110100 AD <-> GND
+ // 0b1110111 AD <-> VCC
+ // 0b1110101 AD <-> SCL
+ // 0b1110110 AD <-> SDA
+ #define LED_DRIVER_ADDR_1 0b1110100
+ #define LED_DRIVER_ADDR_2 0b1110110
+
+ #define LED_DRIVER_COUNT 2
+ #define LED_DRIVER_1_LED_TOTAL 25
+ #define LED_DRIVER_2_LED_TOTAL 24
+ #define LED_DRIVER_LED_TOTAL LED_DRIVER_1_LED_TOTAL + LED_DRIVER_2_LED_TOTAL
+
+Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.
+
+Define these arrays listing all the LEDs in your `<keyboard>.c`:
+
+ const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
+ /* Refer to IS31 manual for these locations
+ * driver
+ * | R location
+ * | | G location
+ * | | | B location
+ * | | | | */
+ {0, C1_3, C2_3, C3_3},
+ ....
+ }
+
+Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3731.pdf) and the header file `drivers/issi/is31fl3731.h`. The `driver` is the index of the driver you defined in your `config.h` (`0` or `1` right now).
+
+### IS31FL3733
+
+There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`:
+
+ RGB_MATRIX_ENABLE = IS31FL3733
+
+Configure the hardware via your `config.h`:
+
+ // This is a 7-bit address, that gets left-shifted and bit 0
+ // set to 0 for write, 1 for read (as per I2C protocol)
+ // The address will vary depending on your wiring:
+ // 00 <-> GND
+ // 01 <-> SCL
+ // 10 <-> SDA
+ // 11 <-> VCC
+ // ADDR1 represents A1:A0 of the 7-bit address.
+ // ADDR2 represents A3:A2 of the 7-bit address.
+ // The result is: 0b101(ADDR2)(ADDR1)
+ #define DRIVER_ADDR_1 0b1010000
+ #define DRIVER_ADDR_2 0b1010000 // this is here for compliancy reasons.
+
+ #define DRIVER_COUNT 1
+ #define DRIVER_1_LED_TOTAL 64
+ #define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL
+
+Currently only a single drivers is supported, but it would be trivial to support all 4 combinations. For now define `DRIVER_ADDR_2` as `DRIVER_ADDR_1`
+
+Define these arrays listing all the LEDs in your `<keyboard>.c`:
+
+ const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
+ /* Refer to IS31 manual for these locations
+ * driver
+ * | R location
+ * | | G location
+ * | | | B location
+ * | | | | */
+ {0, B_1, A_1, C_1},
+ ....
+ }
+
+Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3733.pdf) and the header file `drivers/issi/is31fl3733.h`. The `driver` is the index of the driver you defined in your `config.h` (Only `0` right now).
+
+From this point forward the configuration is the same for all the drivers.
+
+ const rgb_led g_rgb_leds[DRIVER_LED_TOTAL] = {
+ /* {row | col << 4}
+ * | {x=0..224, y=0..64}
+ * | | modifier
+ * | | | */
+ {{0|(0<<4)}, {20.36*0, 21.33*0}, 1},
+ {{0|(1<<4)}, {20.36*1, 21.33*0}, 1},
+ ....
+ }
+
+The format for the matrix position used in this array is `{row | (col << 4)}`. The `x` is between (inclusive) 0-224, and `y` is between (inclusive) 0-64. The easiest way to calculate these positions is:
+
+ x = 224 / ( NUMBER_OF_ROWS - 1 ) * ROW_POSITION
+ y = 64 / (NUMBER_OF_COLS - 1 ) * COL_POSITION
+
+Where all variables are decimels/floats.
+
+`modifier` is a boolean, whether or not a certain key is considered a modifier (used in some effects).
+
+## Keycodes
+
+All RGB keycodes are currently shared with the RGBLIGHT system:
+
+ * `RGB_TOG` - toggle
+ * `RGB_MOD` - cycle through modes
+ * `RGB_HUI` - increase hue
+ * `RGB_HUD` - decrease hue
+ * `RGB_SAI` - increase saturation
+ * `RGB_SAD` - decrease saturation
+ * `RGB_VAI` - increase value
+ * `RGB_VAD` - decrease value
+ * `RGB_SPI` - increase speed effect (no EEPROM support)
+ * `RGB_SPD` - decrease speed effect (no EEPROM support)
+
+
+ * `RGB_MODE_*` keycodes will generally work, but are not currently mapped to the correct effects for the RGB Matrix system
+
+## RGB Matrix Effects
+
+These are the effects that are currently available:
+
+ enum rgb_matrix_effects {
+ RGB_MATRIX_SOLID_COLOR = 1,
+ RGB_MATRIX_ALPHAS_MODS,
+ RGB_MATRIX_DUAL_BEACON,
+ RGB_MATRIX_GRADIENT_UP_DOWN,
+ RGB_MATRIX_RAINDROPS,
+ RGB_MATRIX_CYCLE_ALL,
+ RGB_MATRIX_CYCLE_LEFT_RIGHT,
+ RGB_MATRIX_CYCLE_UP_DOWN,
+ RGB_MATRIX_RAINBOW_BEACON,
+ RGB_MATRIX_RAINBOW_PINWHEELS,
+ RGB_MATRIX_RAINBOW_MOVING_CHEVRON,
+ RGB_MATRIX_JELLYBEAN_RAINDROPS,
+ RGB_MATRIX_DIGITAL_RAIN,
+ #ifdef RGB_MATRIX_KEYPRESSES
+ RGB_MATRIX_SOLID_REACTIVE,
+ RGB_MATRIX_SPLASH,
+ RGB_MATRIX_MULTISPLASH,
+ RGB_MATRIX_SOLID_SPLASH,
+ RGB_MATRIX_SOLID_MULTISPLASH,
+ #endif
+ RGB_MATRIX_EFFECT_MAX
+ };
+
+You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `config.h`:
+
+
+|Define |Description |
+|---------------------------------------------------|--------------------------------------------|
+|`#define DISABLE_RGB_MATRIX_ALPHAS_MODS` |Disables `RGB_MATRIX_ALPHAS_MODS` |
+|`#define DISABLE_RGB_MATRIX_DUAL_BEACON` |Disables `RGB_MATRIX_DUAL_BEACON` |
+|`#define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN` |Disables `RGB_MATRIX_GRADIENT_UP_DOWN` |
+|`#define DISABLE_RGB_MATRIX_RAINDROPS` |Disables `RGB_MATRIX_RAINDROPS` |
+|`#define DISABLE_RGB_MATRIX_CYCLE_ALL` |Disables `RGB_MATRIX_CYCLE_ALL` |
+|`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT` |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT` |
+|`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN` |Disables `RGB_MATRIX_CYCLE_UP_DOWN` |
+|`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON` |Disables `RGB_MATRIX_RAINBOW_BEACON` |
+|`#define DISABLE_RGB_MATRIX_RAINBOW_PINWHEELS` |Disables `RGB_MATRIX_RAINBOW_PINWHEELS` |
+|`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|
+|`#define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS` |Disables `RGB_MATRIX_JELLYBEAN_RAINDROPS` |
+|`#define DISABLE_RGB_MATRIX_DIGITAL_RAIN` |Disables `RGB_MATRIX_DIGITAL_RAIN` |
+|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE` |Disables `RGB_MATRIX_SOLID_REACTIVE` |
+|`#define DISABLE_RGB_MATRIX_SPLASH` |Disables `RGB_MATRIX_SPLASH` |
+|`#define DISABLE_RGB_MATRIX_MULTISPLASH` |Disables `RGB_MATRIX_MULTISPLASH` |
+|`#define DISABLE_RGB_MATRIX_SOLID_SPLASH` |Disables `RGB_MATRIX_SOLID_SPLASH` |
+|`#define DISABLE_RGB_MATRIX_SOLID_MULTISPLASH` |Disables `RGB_MATRIX_SOLID_MULTISPLASH` |
+
+
+## Custom layer effects
+
+Custom layer effects can be done by defining this in your `<keyboard>.c`:
+
+ void rgb_matrix_indicators_kb(void) {
+ rgb_matrix_set_color(index, red, green, blue);
+ }
+
+A similar function works in the keymap as `rgb_matrix_indicators_user`.
+
+## Additional `config.h` Options
+
+ #define RGB_MATRIX_KEYPRESSES // reacts to keypresses (will slow down matrix scan by a lot)
+ #define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (not recommened)
+ #define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
+ #define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
+ #define RGB_MATRIX_SKIP_FRAMES 1 // number of frames to skip when displaying animations (0 is full effect) if not defined defaults to 1
+ #define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255
+
+## EEPROM storage
+
+The EEPROM for it is currently shared with the RGBLIGHT system (it's generally assumed only one RGB would be used at a time), but could be configured to use its own 32bit address with:
+
+ #define EECONFIG_RGB_MATRIX (uint32_t *)16
+
+Where `16` is an unused index from `eeconfig.h`.
+
+## Suspended state
+
+To use the suspend feature, add this to your `<keyboard>.c`:
+
+ void suspend_power_down_kb(void)
+ {
+ rgb_matrix_set_suspend_state(true);
+ }
+
+ void suspend_wakeup_init_kb(void)
+ {
+ rgb_matrix_set_suspend_state(false);
+ }
A drivers/issi/is31fl3731-simple.c => drivers/issi/is31fl3731-simple.c +240 -0
@@ 0,0 1,240 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifdef __AVR__
+#include <avr/interrupt.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#else
+#include "wait.h"
+#endif
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <string.h>
+#include "is31fl3731-simple.h"
+#include "i2c_master.h"
+#include "progmem.h"
+
+// This is a 7-bit address, that gets left-shifted and bit 0
+// set to 0 for write, 1 for read (as per I2C protocol)
+// The address will vary depending on your wiring:
+// 0b1110100 AD <-> GND
+// 0b1110111 AD <-> VCC
+// 0b1110101 AD <-> SCL
+// 0b1110110 AD <-> SDA
+#define ISSI_ADDR_DEFAULT 0x74
+
+#define ISSI_REG_CONFIG 0x00
+#define ISSI_REG_CONFIG_PICTUREMODE 0x00
+#define ISSI_REG_CONFIG_AUTOPLAYMODE 0x08
+#define ISSI_REG_CONFIG_AUDIOPLAYMODE 0x18
+
+#define ISSI_CONF_PICTUREMODE 0x00
+#define ISSI_CONF_AUTOFRAMEMODE 0x04
+#define ISSI_CONF_AUDIOMODE 0x08
+
+#define ISSI_REG_PICTUREFRAME 0x01
+
+#define ISSI_REG_SHUTDOWN 0x0A
+#define ISSI_REG_AUDIOSYNC 0x06
+
+#define ISSI_COMMANDREGISTER 0xFD
+#define ISSI_BANK_FUNCTIONREG 0x0B // helpfully called 'page nine'
+
+#ifndef ISSI_TIMEOUT
+ #define ISSI_TIMEOUT 100
+#endif
+
+#ifndef ISSI_PERSISTENCE
+ #define ISSI_PERSISTENCE 0
+#endif
+
+// Transfer buffer for TWITransmitData()
+uint8_t g_twi_transfer_buffer[20];
+
+// These buffers match the IS31FL3731 PWM registers 0x24-0xB3.
+// Storing them like this is optimal for I2C transfers to the registers.
+// We could optimize this and take out the unused registers from these
+// buffers and the transfers in IS31FL3731_write_pwm_buffer() but it's
+// probably not worth the extra complexity.
+uint8_t g_pwm_buffer[DRIVER_COUNT][144];
+bool g_pwm_buffer_update_required = false;
+
+uint8_t g_led_control_registers[DRIVER_COUNT][18] = { { 0 }, { 0 } };
+bool g_led_control_registers_update_required = false;
+
+// This is the bit pattern in the LED control registers
+// (for matrix A, add one to register for matrix B)
+//
+// reg - b7 b6 b5 b4 b3 b2 b1 b0
+// 0x00 - R08,R07,R06,R05,R04,R03,R02,R01
+// 0x02 - G08,G07,G06,G05,G04,G03,G02,R00
+// 0x04 - B08,B07,B06,B05,B04,B03,G01,G00
+// 0x06 - - , - , - , - , - ,B02,B01,B00
+// 0x08 - - , - , - , - , - , - , - , -
+// 0x0A - B17,B16,B15, - , - , - , - , -
+// 0x0C - G17,G16,B14,B13,B12,B11,B10,B09
+// 0x0E - R17,G15,G14,G13,G12,G11,G10,G09
+// 0x10 - R16,R15,R14,R13,R12,R11,R10,R09
+
+
+void IS31FL3731_write_register(uint8_t addr, uint8_t reg, uint8_t data) {
+ g_twi_transfer_buffer[0] = reg;
+ g_twi_transfer_buffer[1] = data;
+
+ #if ISSI_PERSISTENCE > 0
+ for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+ if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0) {
+ break;
+ }
+ }
+ #else
+ i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT);
+ #endif
+}
+
+void IS31FL3731_write_pwm_buffer(uint8_t addr, uint8_t *pwm_buffer) {
+ // assumes bank is already selected
+
+ // transmit PWM registers in 9 transfers of 16 bytes
+ // g_twi_transfer_buffer[] is 20 bytes
+
+ // iterate over the pwm_buffer contents at 16 byte intervals
+ for (int i = 0; i < 144; i += 16) {
+ // set the first register, e.g. 0x24, 0x34, 0x44, etc.
+ g_twi_transfer_buffer[0] = 0x24 + i;
+ // copy the data from i to i+15
+ // device will auto-increment register for data after the first byte
+ // thus this sets registers 0x24-0x33, 0x34-0x43, etc. in one transfer
+ for (int j = 0; j < 16; j++) {
+ g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j];
+ }
+
+ #if ISSI_PERSISTENCE > 0
+ for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+ if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0)
+ break;
+ }
+ #else
+ i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT);
+ #endif
+ }
+}
+
+void IS31FL3731_init(uint8_t addr) {
+ // In order to avoid the LEDs being driven with garbage data
+ // in the LED driver's PWM registers, first enable software shutdown,
+ // then set up the mode and other settings, clear the PWM registers,
+ // then disable software shutdown.
+
+ // select "function register" bank
+ IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG);
+
+ // enable software shutdown
+ IS31FL3731_write_register(addr, ISSI_REG_SHUTDOWN, 0x00);
+ // this delay was copied from other drivers, might not be needed
+ // FIXME: Don't we have a wrapper for this already?
+ #ifdef __AVR__
+ _delay_ms(10);
+ #else
+ wait_ms(10);
+ #endif
+
+ // picture mode
+ IS31FL3731_write_register(addr, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE);
+ // display frame 0
+ IS31FL3731_write_register(addr, ISSI_REG_PICTUREFRAME, 0x00);
+ // audio sync off
+ IS31FL3731_write_register(addr, ISSI_REG_AUDIOSYNC, 0x00);
+
+ // select bank 0
+ IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, 0);
+
+ // turn off all LEDs in the LED control register
+ for (int i = 0x00; i <= 0x11; i++) {
+ IS31FL3731_write_register(addr, i, 0x00);
+ }
+
+ // turn off all LEDs in the blink control register (not really needed)
+ for (int i = 0x12; i <= 0x23; i++) {
+ IS31FL3731_write_register(addr, i, 0x00);
+ }
+
+ // set PWM on all LEDs to 0
+ for (int i = 0x24; i <= 0xB3; i++) {
+ IS31FL3731_write_register(addr, i, 0x00);
+ }
+
+ // select "function register" bank
+ IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG);
+
+ // disable software shutdown
+ IS31FL3731_write_register(addr, ISSI_REG_SHUTDOWN, 0x01);
+
+ // select bank 0 and leave it selected.
+ // most usage after initialization is just writing PWM buffers in bank 0
+ // as there's not much point in double-buffering
+ IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, 0);
+
+}
+
+void IS31FL3731_set_value(int index, uint8_t value) {
+ if (index >= 0 && index < DRIVER_LED_TOTAL) {
+ is31_led led = g_is31_leds[index];
+
+ // Subtract 0x24 to get the second index of g_pwm_buffer
+ g_pwm_buffer[led.driver][led.v - 0x24] = value;
+ g_pwm_buffer_update_required = true;
+ }
+}
+
+void IS31FL3731_set_value_all(uint8_t value) {
+ for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
+ IS31FL3731_set_value(i, value);
+ }
+}
+
+void IS31FL3731_set_led_control_register(uint8_t index, bool value) {
+ is31_led led = g_is31_leds[index];
+
+ uint8_t control_register = (led.v - 0x24) / 8;
+ uint8_t bit_value = (led.v - 0x24) % 8;
+
+ if (value) {
+ g_led_control_registers[led.driver][control_register] |= (1 << bit_value);
+ } else {
+ g_led_control_registers[led.driver][control_register] &= ~(1 << bit_value);
+ }
+
+ g_led_control_registers_update_required = true;
+}
+
+void IS31FL3731_update_pwm_buffers(uint8_t addr, uint8_t index) {
+ if (g_pwm_buffer_update_required) {
+ IS31FL3731_write_pwm_buffer(addr, g_pwm_buffer[index]);
+ g_pwm_buffer_update_required = false;
+ }
+}
+
+void IS31FL3731_update_led_control_registers(uint8_t addr, uint8_t index) {
+ if (g_led_control_registers_update_required) {
+ for (int i=0; i<18; i++) {
+ IS31FL3731_write_register(addr, i, g_led_control_registers[index][i]);
+ }
+ }
+}
A drivers/issi/is31fl3731-simple.h => drivers/issi/is31fl3731-simple.h +209 -0
@@ 0,0 1,209 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef IS31FL3731_DRIVER_H
+#define IS31FL3731_DRIVER_H
+
+
+typedef struct is31_led {
+ uint8_t driver:2;
+ uint8_t v;
+} __attribute__((packed)) is31_led;
+
+extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
+
+void IS31FL3731_init(uint8_t addr);
+void IS31FL3731_write_register(uint8_t addr, uint8_t reg, uint8_t data);
+void IS31FL3731_write_pwm_buffer(uint8_t addr, uint8_t *pwm_buffer);
+
+void IS31FL3731_set_value(int index, uint8_t value);
+void IS31FL3731_set_value_all(uint8_t value);
+
+void IS31FL3731_set_led_control_register(uint8_t index, bool value);
+
+// This should not be called from an interrupt
+// (eg. from a timer interrupt).
+// Call this while idle (in between matrix scans).
+// If the buffer is dirty, it will update the driver with the buffer.
+void IS31FL3731_update_pwm_buffers(uint8_t addr, uint8_t index);
+void IS31FL3731_update_led_control_registers(uint8_t addr, uint8_t index);
+
+#define C1_1 0x24
+#define C1_2 0x25
+#define C1_3 0x26
+#define C1_4 0x27
+#define C1_5 0x28
+#define C1_6 0x29
+#define C1_7 0x2A
+#define C1_8 0x2B
+
+#define C1_9 0x2C
+#define C1_10 0x2D
+#define C1_11 0x2E
+#define C1_12 0x2F
+#define C1_13 0x30
+#define C1_14 0x31
+#define C1_15 0x32
+#define C1_16 0x33
+
+#define C2_1 0x34
+#define C2_2 0x35
+#define C2_3 0x36
+#define C2_4 0x37
+#define C2_5 0x38
+#define C2_6 0x39
+#define C2_7 0x3A
+#define C2_8 0x3B
+
+#define C2_9 0x3C
+#define C2_10 0x3D
+#define C2_11 0x3E
+#define C2_12 0x3F
+#define C2_13 0x40
+#define C2_14 0x41
+#define C2_15 0x42
+#define C2_16 0x43
+
+#define C3_1 0x44
+#define C3_2 0x45
+#define C3_3 0x46
+#define C3_4 0x47
+#define C3_5 0x48
+#define C3_6 0x49
+#define C3_7 0x4A
+#define C3_8 0x4B
+
+#define C3_9 0x4C
+#define C3_10 0x4D
+#define C3_11 0x4E
+#define C3_12 0x4F
+#define C3_13 0x50
+#define C3_14 0x51
+#define C3_15 0x52
+#define C3_16 0x53
+
+#define C4_1 0x54
+#define C4_2 0x55
+#define C4_3 0x56
+#define C4_4 0x57
+#define C4_5 0x58
+#define C4_6 0x59
+#define C4_7 0x5A
+#define C4_8 0x5B
+
+#define C4_9 0x5C
+#define C4_10 0x5D
+#define C4_11 0x5E
+#define C4_12 0x5F
+#define C4_13 0x60
+#define C4_14 0x61
+#define C4_15 0x62
+#define C4_16 0x63
+
+#define C5_1 0x64
+#define C5_2 0x65
+#define C5_3 0x66
+#define C5_4 0x67
+#define C5_5 0x68
+#define C5_6 0x69
+#define C5_7 0x6A
+#define C5_8 0x6B
+
+#define C5_9 0x6C
+#define C5_10 0x6D
+#define C5_11 0x6E
+#define C5_12 0x6F
+#define C5_13 0x70
+#define C5_14 0x71
+#define C5_15 0x72
+#define C5_16 0x73
+
+#define C6_1 0x74
+#define C6_2 0x75
+#define C6_3 0x76
+#define C6_4 0x77
+#define C6_5 0x78
+#define C6_6 0x79
+#define C6_7 0x7A
+#define C6_8 0x7B
+
+#define C6_9 0x7C
+#define C6_10 0x7D
+#define C6_11 0x7E
+#define C6_12 0x7F
+#define C6_13 0x80
+#define C6_14 0x81
+#define C6_15 0x82
+#define C6_16 0x83
+
+#define C7_1 0x84
+#define C7_2 0x85
+#define C7_3 0x86
+#define C7_4 0x87
+#define C7_5 0x88
+#define C7_6 0x89
+#define C7_7 0x8A
+#define C7_8 0x8B
+
+#define C7_9 0x8C
+#define C7_10 0x8D
+#define C7_11 0x8E
+#define C7_12 0x8F
+#define C7_13 0x90
+#define C7_14 0x91
+#define C7_15 0x92
+#define C7_16 0x93
+
+#define C8_1 0x94
+#define C8_2 0x95
+#define C8_3 0x96
+#define C8_4 0x97
+#define C8_5 0x98
+#define C8_6 0x99
+#define C8_7 0x9A
+#define C8_8 0x9B
+
+#define C8_9 0x9C
+#define C8_10 0x9D
+#define C8_11 0x9E
+#define C8_12 0x9F
+#define C8_13 0xA0
+#define C8_14 0xA1
+#define C8_15 0xA2
+#define C8_16 0xA3
+
+#define C9_1 0xA4
+#define C9_2 0xA5
+#define C9_3 0xA6
+#define C9_4 0xA7
+#define C9_5 0xA8
+#define C9_6 0xA9
+#define C9_7 0xAA
+#define C9_8 0xAB
+
+#define C9_9 0xAC
+#define C9_10 0xAD
+#define C9_11 0xAE
+#define C9_12 0xAF
+#define C9_13 0xB0
+#define C9_14 0xB1
+#define C9_15 0xB2
+#define C9_16 0xB3
+
+
+#endif // IS31FL3731_DRIVER_H
A quantum/led_matrix.c => quantum/led_matrix.c +404 -0
@@ 0,0 1,404 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2017 Jack Humbert
+ * Copyright 2018 Yiancar
+ * Copyright 2019 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <stdint.h>
+#include <stdbool.h>
+#include "quantum.h"
+#include "led_matrix.h"
+#include "progmem.h"
+#include "config.h"
+#include "eeprom.h"
+#include <string.h>
+#include <math.h>
+
+led_config_t led_matrix_config;
+
+#ifndef MAX
+ #define MAX(X, Y) ((X) > (Y) ? (X) : (Y))
+#endif
+
+#ifndef MIN
+ #define MIN(a,b) ((a) < (b)? (a): (b))
+#endif
+
+#ifndef LED_DISABLE_AFTER_TIMEOUT
+ #define LED_DISABLE_AFTER_TIMEOUT 0
+#endif
+
+#ifndef LED_DISABLE_WHEN_USB_SUSPENDED
+ #define LED_DISABLE_WHEN_USB_SUSPENDED false
+#endif
+
+#ifndef EECONFIG_LED_MATRIX
+ #define EECONFIG_LED_MATRIX EECONFIG_RGBLIGHT
+#endif
+
+#if !defined(LED_MATRIX_MAXIMUM_BRIGHTNESS) || LED_MATRIX_MAXIMUM_BRIGHTNESS > 255
+ #define LED_MATRIX_MAXIMUM_BRIGHTNESS 255
+#endif
+
+bool g_suspend_state = false;
+
+// Global tick at 20 Hz
+uint32_t g_tick = 0;
+
+// Ticks since this key was last hit.
+uint8_t g_key_hit[DRIVER_LED_TOTAL];
+
+// Ticks since any key was last hit.
+uint32_t g_any_key_hit = 0;
+
+uint32_t eeconfig_read_led_matrix(void) {
+ return eeprom_read_dword(EECONFIG_LED_MATRIX);
+}
+void eeconfig_update_led_matrix(uint32_t config_value) {
+ eeprom_update_dword(EECONFIG_LED_MATRIX, config_value);
+}
+void eeconfig_update_led_matrix_default(void) {
+ dprintf("eeconfig_update_led_matrix_default\n");
+ led_matrix_config.enable = 1;
+ led_matrix_config.mode = LED_MATRIX_UNIFORM_BRIGHTNESS;
+ led_matrix_config.val = 128;
+ led_matrix_config.speed = 0;
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+void eeconfig_debug_led_matrix(void) {
+ dprintf("led_matrix_config eprom\n");
+ dprintf("led_matrix_config.enable = %d\n", led_matrix_config.enable);
+ dprintf("led_matrix_config.mode = %d\n", led_matrix_config.mode);
+ dprintf("led_matrix_config.val = %d\n", led_matrix_config.val);
+ dprintf("led_matrix_config.speed = %d\n", led_matrix_config.speed);
+}
+
+// Last led hit
+#define LED_HITS_TO_REMEMBER 8
+uint8_t g_last_led_hit[LED_HITS_TO_REMEMBER] = {255};
+uint8_t g_last_led_count = 0;
+
+void map_row_column_to_led(uint8_t row, uint8_t column, uint8_t *led_i, uint8_t *led_count) {
+ led_matrix led;
+ *led_count = 0;
+
+ for (uint8_t i = 0; i < DRIVER_LED_TOTAL; i++) {
+ // map_index_to_led(i, &led);
+ led = g_leds[i];
+ if (row == led.matrix_co.row && column == led.matrix_co.col) {
+ led_i[*led_count] = i;
+ (*led_count)++;
+ }
+ }
+}
+
+void led_matrix_update_pwm_buffers(void) {
+ led_matrix_driver.flush();
+}
+
+void led_matrix_set_index_value(int index, uint8_t value) {
+ led_matrix_driver.set_value(index, value);
+}
+
+void led_matrix_set_index_value_all(uint8_t value) {
+ led_matrix_driver.set_value_all(value);
+}
+
+bool process_led_matrix(uint16_t keycode, keyrecord_t *record) {
+ if (record->event.pressed) {
+ uint8_t led[8], led_count;
+ map_row_column_to_led(record->event.key.row, record->event.key.col, led, &led_count);
+ if (led_count > 0) {
+ for (uint8_t i = LED_HITS_TO_REMEMBER; i > 1; i--) {
+ g_last_led_hit[i - 1] = g_last_led_hit[i - 2];
+ }
+ g_last_led_hit[0] = led[0];
+ g_last_led_count = MIN(LED_HITS_TO_REMEMBER, g_last_led_count + 1);
+ }
+ for(uint8_t i = 0; i < led_count; i++)
+ g_key_hit[led[i]] = 0;
+ g_any_key_hit = 0;
+ } else {
+ #ifdef LED_MATRIX_KEYRELEASES
+ uint8_t led[8], led_count;
+ map_row_column_to_led(record->event.key.row, record->event.key.col, led, &led_count);
+ for(uint8_t i = 0; i < led_count; i++)
+ g_key_hit[led[i]] = 255;
+
+ g_any_key_hit = 255;
+ #endif
+ }
+ return true;
+}
+
+void led_matrix_set_suspend_state(bool state) {
+ g_suspend_state = state;
+}
+
+// All LEDs off
+void led_matrix_all_off(void) {
+ led_matrix_set_index_value_all(0);
+}
+
+// Uniform brightness
+void led_matrix_uniform_brightness(void) {
+ led_matrix_set_index_value_all(led_matrix_config.val);
+}
+
+void led_matrix_custom(void) {}
+
+void led_matrix_task(void) {
+ #ifdef TRACK_PREVIOUS_EFFECT
+ static uint8_t toggle_enable_last = 255;
+ #endif
+ if (!led_matrix_config.enable) {
+ led_matrix_all_off();
+ led_matrix_indicators();
+ #ifdef TRACK_PREVIOUS_EFFECT
+ toggle_enable_last = led_matrix_config.enable;
+ #endif
+ return;
+ }
+
+ // delay 1 second before driving LEDs or doing anything else
+ // FIXME: Can't we use wait_ms() here?
+ static uint8_t startup_tick = 0;
+ if (startup_tick < 20) {
+ startup_tick++;
+ return;
+ }
+
+ g_tick++;
+
+ if (g_any_key_hit < 0xFFFFFFFF) {
+ g_any_key_hit++;
+ }
+
+ for (int led = 0; led < DRIVER_LED_TOTAL; led++) {
+ if (g_key_hit[led] < 255) {
+ if (g_key_hit[led] == 254)
+ g_last_led_count = MAX(g_last_led_count - 1, 0);
+ g_key_hit[led]++;
+ }
+ }
+
+ // Factory default magic value
+ if (led_matrix_config.mode == 255) {
+ led_matrix_uniform_brightness();
+ return;
+ }
+
+ // Ideally we would also stop sending zeros to the LED driver PWM buffers
+ // while suspended and just do a software shutdown. This is a cheap hack for now.
+ bool suspend_backlight = ((g_suspend_state && LED_DISABLE_WHEN_USB_SUSPENDED) ||
+ (LED_DISABLE_AFTER_TIMEOUT > 0 && g_any_key_hit > LED_DISABLE_AFTER_TIMEOUT * 60 * 20));
+ uint8_t effect = suspend_backlight ? 0 : led_matrix_config.mode;
+
+ #ifdef TRACK_PREVIOUS_EFFECT
+ // Keep track of the effect used last time,
+ // detect change in effect, so each effect can
+ // have an optional initialization.
+
+ static uint8_t effect_last = 255;
+ bool initialize = (effect != effect_last) || (led_matrix_config.enable != toggle_enable_last);
+ effect_last = effect;
+ toggle_enable_last = led_matrix_config.enable;
+ #endif
+
+ // this gets ticked at 20 Hz.
+ // each effect can opt to do calculations
+ // and/or request PWM buffer updates.
+ switch (effect) {
+ case LED_MATRIX_UNIFORM_BRIGHTNESS:
+ led_matrix_uniform_brightness();
+ break;
+ default:
+ led_matrix_custom();
+ break;
+ }
+
+ if (! suspend_backlight) {
+ led_matrix_indicators();
+ }
+
+}
+
+void led_matrix_indicators(void) {
+ led_matrix_indicators_kb();
+ led_matrix_indicators_user();
+}
+
+__attribute__((weak))
+void led_matrix_indicators_kb(void) {}
+
+__attribute__((weak))
+void led_matrix_indicators_user(void) {}
+
+
+// void led_matrix_set_indicator_index(uint8_t *index, uint8_t row, uint8_t column)
+// {
+// if (row >= MATRIX_ROWS)
+// {
+// // Special value, 255=none, 254=all
+// *index = row;
+// }
+// else
+// {
+// // This needs updated to something like
+// // uint8_t led[8], led_count;
+// // map_row_column_to_led(row,column,led,&led_count);
+// // for(uint8_t i = 0; i < led_count; i++)
+// map_row_column_to_led(row, column, index);
+// }
+// }
+
+void led_matrix_init(void) {
+ led_matrix_driver.init();
+
+ // TODO: put the 1 second startup delay here?
+
+ // clear the key hits
+ for (int led=0; led<DRIVER_LED_TOTAL; led++) {
+ g_key_hit[led] = 255;
+ }
+
+
+ if (!eeconfig_is_enabled()) {
+ dprintf("led_matrix_init_drivers eeconfig is not enabled.\n");
+ eeconfig_init();
+ eeconfig_update_led_matrix_default();
+ }
+ led_matrix_config.raw = eeconfig_read_led_matrix();
+ if (!led_matrix_config.mode) {
+ dprintf("led_matrix_init_drivers led_matrix_config.mode = 0. Write default values to EEPROM.\n");
+ eeconfig_update_led_matrix_default();
+ led_matrix_config.raw = eeconfig_read_led_matrix();
+ }
+ eeconfig_debug_led_matrix(); // display current eeprom values
+}
+
+// Deals with the messy details of incrementing an integer
+static uint8_t increment(uint8_t value, uint8_t step, uint8_t min, uint8_t max) {
+ int16_t new_value = value;
+ new_value += step;
+ return MIN(MAX( new_value, min), max );
+}
+
+static uint8_t decrement(uint8_t value, uint8_t step, uint8_t min, uint8_t max) {
+ int16_t new_value = value;
+ new_value -= step;
+ return MIN(MAX( new_value, min), max );
+}
+
+// void *backlight_get_custom_key_value_eeprom_address(uint8_t led) {
+// // 3 bytes per value
+// return EECONFIG_LED_MATRIX + (led * 3);
+// }
+
+// void backlight_get_key_value(uint8_t led, uint8_t *value) {
+// void *address = backlight_get_custom_key_value_eeprom_address(led);
+// value = eeprom_read_byte(address);
+// }
+
+// void backlight_set_key_value(uint8_t row, uint8_t column, uint8_t value) {
+// uint8_t led[8], led_count;
+// map_row_column_to_led(row,column,led,&led_count);
+// for(uint8_t i = 0; i < led_count; i++) {
+// if (led[i] < DRIVER_LED_TOTAL) {
+// void *address = backlight_get_custom_key_value_eeprom_address(led[i]);
+// eeprom_update_byte(address, value);
+// }
+// }
+// }
+
+uint32_t led_matrix_get_tick(void) {
+ return g_tick;
+}
+
+void led_matrix_toggle(void) {
+ led_matrix_config.enable ^= 1;
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_enable(void) {
+ led_matrix_config.enable = 1;
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_enable_noeeprom(void) {
+ led_matrix_config.enable = 1;
+}
+
+void led_matrix_disable(void) {
+ led_matrix_config.enable = 0;
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_disable_noeeprom(void) {
+ led_matrix_config.enable = 0;
+}
+
+void led_matrix_step(void) {
+ led_matrix_config.mode++;
+ if (led_matrix_config.mode >= LED_MATRIX_EFFECT_MAX)
+ led_matrix_config.mode = 1;
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_step_reverse(void) {
+ led_matrix_config.mode--;
+ if (led_matrix_config.mode < 1)
+ led_matrix_config.mode = LED_MATRIX_EFFECT_MAX - 1;
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_increase_val(void) {
+ led_matrix_config.val = increment(led_matrix_config.val, 8, 0, LED_MATRIX_MAXIMUM_BRIGHTNESS);
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_decrease_val(void) {
+ led_matrix_config.val = decrement(led_matrix_config.val, 8, 0, LED_MATRIX_MAXIMUM_BRIGHTNESS);
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+}
+
+void led_matrix_increase_speed(void) {
+ led_matrix_config.speed = increment(led_matrix_config.speed, 1, 0, 3);
+ eeconfig_update_led_matrix(led_matrix_config.raw);//EECONFIG needs to be increased to support this
+}
+
+void led_matrix_decrease_speed(void) {
+ led_matrix_config.speed = decrement(led_matrix_config.speed, 1, 0, 3);
+ eeconfig_update_led_matrix(led_matrix_config.raw);//EECONFIG needs to be increased to support this
+}
+
+void led_matrix_mode(uint8_t mode, bool eeprom_write) {
+ led_matrix_config.mode = mode;
+ if (eeprom_write) {
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+ }
+}
+
+uint8_t led_matrix_get_mode(void) {
+ return led_matrix_config.mode;
+}
+
+void led_matrix_set_value(uint8_t val, bool eeprom_write) {
+ led_matrix_config.val = val;
+ if (eeprom_write) {
+ eeconfig_update_led_matrix(led_matrix_config.raw);
+ }
+}
A quantum/led_matrix.h => quantum/led_matrix.h +142 -0
@@ 0,0 1,142 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2017 Jack Humbert
+ * Copyright 2018 Yiancar
+ * Copyright 2019 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef LED_MATRIX_H
+#define LED_MATRIX_H
+
+
+typedef struct Point {
+ uint8_t x;
+ uint8_t y;
+} __attribute__((packed)) Point;
+
+typedef struct led_matrix {
+ union {
+ uint8_t raw;
+ struct {
+ uint8_t row:4; // 16 max
+ uint8_t col:4; // 16 max
+ };
+ } matrix_co;
+ Point point;
+ uint8_t modifier:1;
+} __attribute__((packed)) led_matrix;
+
+extern const led_matrix g_leds[DRIVER_LED_TOTAL];
+
+typedef struct {
+ uint8_t index;
+ uint8_t value;
+} led_indicator;
+
+typedef union {
+ uint32_t raw;
+ struct {
+ bool enable :1;
+ uint8_t mode :6;
+ uint8_t hue :8; // Unused by led_matrix
+ uint8_t sat :8; // Unused by led_matrix
+ uint8_t val :8;
+ uint8_t speed :8;//EECONFIG needs to be increased to support this
+ };
+} led_config_t;
+
+enum led_matrix_effects {
+ LED_MATRIX_UNIFORM_BRIGHTNESS = 1,
+ // All new effects go above this line
+ LED_MATRIX_EFFECT_MAX
+};
+
+void led_matrix_set_index_value(int index, uint8_t value);
+void led_matrix_set_index_value_all(uint8_t value);
+
+// This runs after another backlight effect and replaces
+// colors already set
+void led_matrix_indicators(void);
+void led_matrix_indicators_kb(void);
+void led_matrix_indicators_user(void);
+
+void led_matrix_init(void);
+void led_matrix_setup_drivers(void);
+
+void led_matrix_set_suspend_state(bool state);
+void led_matrix_set_indicator_state(uint8_t state);
+
+void led_matrix_task(void);
+
+// This should not be called from an interrupt
+// (eg. from a timer interrupt).
+// Call this while idle (in between matrix scans).
+// If the buffer is dirty, it will update the driver with the buffer.
+void led_matrix_update_pwm_buffers(void);
+
+bool process_led_matrix(uint16_t keycode, keyrecord_t *record);
+
+uint32_t led_matrix_get_tick(void);
+
+void led_matrix_toggle(void);
+void led_matrix_enable(void);
+void led_matrix_enable_noeeprom(void);
+void led_matrix_disable(void);
+void led_matrix_disable_noeeprom(void);
+void led_matrix_step(void);
+void led_matrix_step_reverse(void);
+void led_matrix_increase_val(void);
+void led_matrix_decrease_val(void);
+void led_matrix_increase_speed(void);
+void led_matrix_decrease_speed(void);
+void led_matrix_mode(uint8_t mode, bool eeprom_write);
+void led_matrix_mode_noeeprom(uint8_t mode);
+uint8_t led_matrix_get_mode(void);
+void led_matrix_set_value(uint8_t mode, bool eeprom_write);
+
+#ifndef BACKLIGHT_ENABLE
+#define backlight_toggle() backlight_matrix_toggle()
+#define backlight_enable() backlight_matrix_enable()
+#define backlight_enable_noeeprom() backlight_matrix_enable_noeeprom()
+#define backlight_disable() backlight_matrix_disable()
+#define backlight_disable_noeeprom() backlight_matrix_disable_noeeprom()
+#define backlight_step() backlight_matrix_step()
+#define backlight_set_value(val) backlight_matrix_set_value(val)
+#define backlight_set_value_noeeprom(val) backlight_matrix_set_value_noeeprom(val)
+#define backlight_step_reverse() backlight_matrix_step_reverse()
+#define backlight_increase_val() backlight_matrix_increase_val()
+#define backlight_decrease_val() backlight_matrix_decrease_val()
+#define backlight_increase_speed() backlight_matrix_increase_speed()
+#define backlight_decrease_speed() backlight_matrix_decrease_speed()
+#define backlight_mode(mode) backlight_matrix_mode(mode)
+#define backlight_mode_noeeprom(mode) backlight_matrix_mode_noeeprom(mode)
+#define backlight_get_mode() backlight_matrix_get_mode()
+#endif
+
+typedef struct {
+ /* Perform any initialisation required for the other driver functions to work. */
+ void (*init)(void);
+
+ /* Set the brightness of a single LED in the buffer. */
+ void (*set_value)(int index, uint8_t value);
+ /* Set the brightness of all LEDS on the keyboard in the buffer. */
+ void (*set_value_all)(uint8_t value);
+ /* Flush any buffered changes to the hardware. */
+ void (*flush)(void);
+} led_matrix_driver_t;
+
+extern const led_matrix_driver_t led_matrix_driver;
+
+#endif
A quantum/led_matrix_drivers.c => quantum/led_matrix_drivers.c +147 -0
@@ 0,0 1,147 @@
+/* Copyright 2018 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <stdint.h>
+#include <stdbool.h>
+#include "quantum.h"
+#include "led_matrix.h"
+
+/* Each driver needs to define a struct:
+ *
+ * const led_matrix_driver_t led_matrix_driver;
+ *
+ * All members must be provided. Keyboard custom drivers must define this
+ * in their own files.
+ */
+
+#if defined(IS31FL3731) || defined(IS31FL3733)
+
+#if defined(IS31FL3731)
+ #include "is31fl3731-simple.h"
+#endif
+
+#include "i2c_master.h"
+
+static void init(void) {
+ i2c_init();
+ #ifdef IS31FL3731
+ #ifdef LED_DRIVER_ADDR_1
+ IS31FL3731_init(DRIVER_ADDR_1);
+ #endif
+ #ifdef LED_DRIVER_ADDR_2
+ IS31FL3731_init(DRIVER_ADDR_2);
+ #endif
+ #ifdef LED_DRIVER_ADDR_3
+ IS31FL3731_init(DRIVER_ADDR_3);
+ #endif
+ #ifdef LED_DRIVER_ADDR_4
+ IS31FL3731_init(DRIVER_ADDR_4);
+ #endif
+ #else
+ #ifdef LED_DRIVER_ADDR_1
+ IS31FL3733_init(DRIVER_ADDR_1);
+ #endif
+ #ifdef LED_DRIVER_ADDR_2
+ IS31FL3733_init(DRIVER_ADDR_2);
+ #endif
+ #ifdef LED_DRIVER_ADDR_3
+ IS31FL3733_init(DRIVER_ADDR_3);
+ #endif
+ #ifdef LED_DRIVER_ADDR_4
+ IS31FL3733_init(DRIVER_ADDR_4);
+ #endif
+ #endif
+ for (int index = 0; index < DRIVER_LED_TOTAL; index++) {
+ #ifdef IS31FL3731
+ IS31FL3731_set_led_control_register(index, true);
+ #else
+ IS31FL3733_set_led_control_register(index, true);
+ #endif
+ }
+ // This actually updates the LED drivers
+ #ifdef IS31FL3731
+ #ifdef LED_DRIVER_ADDR_1
+ IS31FL3731_update_led_control_registers(DRIVER_ADDR_1);
+ #endif
+ #ifdef LED_DRIVER_ADDR_2
+ IS31FL3731_update_led_control_registers(DRIVER_ADDR_2);
+ #endif
+ #ifdef LED_DRIVER_ADDR_3
+ IS31FL3731_update_led_control_registers(DRIVER_ADDR_3);
+ #endif
+ #ifdef LED_DRIVER_ADDR_4
+ IS31FL3731_update_led_control_registers(DRIVER_ADDR_4);
+ #endif
+ #else
+ #ifdef LED_DRIVER_ADDR_1
+ IS31FL3733_update_led_control_registers(DRIVER_ADDR_1);
+ #endif
+ #ifdef LED_DRIVER_ADDR_2
+ IS31FL3733_update_led_control_registers(DRIVER_ADDR_2);
+ #endif
+ #ifdef LED_DRIVER_ADDR_3
+ IS31FL3733_update_led_control_registers(DRIVER_ADDR_3);
+ #endif
+ #ifdef LED_DRIVER_ADDR_4
+ IS31FL3733_update_led_control_registers(DRIVER_ADDR_4);
+ #endif
+ #endif
+}
+
+static void flush(void) {
+ #ifdef IS31FL3731
+ #ifdef LED_DRIVER_ADDR_1
+ IS31FL3731_update_pwm_buffers(DRIVER_ADDR_1);
+ #endif
+ #ifdef LED_DRIVER_ADDR_2
+ IS31FL3731_update_pwm_buffers(DRIVER_ADDR_2);
+ #endif
+ #ifdef LED_DRIVER_ADDR_3
+ IS31FL3731_update_pwm_buffers(DRIVER_ADDR_3);
+ #endif
+ #ifdef LED_DRIVER_ADDR_4
+ IS31FL3731_update_pwm_buffers(DRIVER_ADDR_4);
+ #endif
+ #else
+ #ifdef LED_DRIVER_ADDR_1
+ IS31FL3733_update_pwm_buffers(DRIVER_ADDR_1);
+ #endif
+ #ifdef LED_DRIVER_ADDR_2
+ IS31FL3733_update_pwm_buffers(DRIVER_ADDR_2);
+ #endif
+ #ifdef LED_DRIVER_ADDR_3
+ IS31FL3733_update_pwm_buffers(DRIVER_ADDR_3);
+ #endif
+ #ifdef LED_DRIVER_ADDR_4
+ IS31FL3733_update_pwm_buffers(DRIVER_ADDR_4);
+ #endif
+ #endif
+}
+
+const led_matrix_driver_t led_matrix_driver = {
+ .init = init,
+ .flush = flush,
+#ifdef IS31FL3731
+ .set_value = IS31FL3731_set_value,
+ .set_value_all = IS31FL3731_set_value_all,
+#else
+ .set_value = IS31FL3733_set_value,
+ .set_value_all = IS31FL3733_set_value_all,
+#endif
+};
+
+
+#endif
M quantum/rgb_matrix.h => quantum/rgb_matrix.h +2 -10
@@ 50,25 50,17 @@ typedef struct rgb_led {
extern const rgb_led g_rgb_leds[DRIVER_LED_TOTAL];
-typedef struct
-{
- HSV color;
- uint8_t index;
-} rgb_indicator;
-
typedef union {
uint32_t raw;
struct {
bool enable :1;
uint8_t mode :6;
- uint16_t hue :9;
- uint8_t sat :8;
uint8_t val :8;
uint8_t speed :8;//EECONFIG needs to be increased to support this
};
-} rgb_config_t;
+} led_config_t;
-enum rgb_matrix_effects {
+enum _matrix_effects {
RGB_MATRIX_SOLID_COLOR = 1,
#ifndef DISABLE_RGB_MATRIX_ALPHAS_MODS
RGB_MATRIX_ALPHAS_MODS,