7 files changed, 203 insertions(+), 0 deletions(-)

A keyboards/yd60mq/config.h
A keyboards/yd60mq/keymaps/default/keymap.c
A keyboards/yd60mq/keymaps/krusli/keymap.c
A keyboards/yd60mq/readme.md
A keyboards/yd60mq/rules.mk
A keyboards/yd60mq/yd60mq.c
A keyboards/yd60mq/yd60mq.h

@@ 0,0 1,47 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    YMDK
+#define PRODUCT         YD60MQ
+#define DESCRIPTION     Keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
+#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, F7, B5, B4, D7, D6, B3, B2 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* number of backlight levels */
+#define BACKLIGHT_PIN B7
+#ifdef BACKLIGHT_PIN
+#define BACKLIGHT_LEVELS 5
+#endif
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* prevent stuck modifiers */
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 12
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif
+

@@ 0,0 1,25 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_BSLS, KC_ENT,
+		KC_LSFT, KC_NUHS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_DEL,
+		KC_LCTL, KC_LGUI, KC_LALT, MO(1), KC_SPC, MO(1), KC_RALT, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
+
+	LAYOUT(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_DEL,
+		KC_TRNS, RGB_TOG, KC_UP, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC, BL_TOGG, BL_INC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};
+
+void matrix_init_user(void) {
+}
+
+void matrix_scan_user(void) {
+}

@@ 0,0 1,19 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+    LAYOUT(
+        KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV,
+        KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC,
+        KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_BSLS, KC_ENT,
+        KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, _______, KC_RSFT, MO(1),
+        KC_LCTL, KC_LALT, KC_LGUI, _______, KC_SPC, _______, _______, KC_RALT, _______, KC_RGUI, KC_RCTL),
+
+    LAYOUT(
+        KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_INS, KC_DEL,
+        KC_CAPS, RGB_TOG, RGB_MOD, RGB_HUI, RGB_VAD, RGB_VAI, RGB_SAD, RGB_SAI, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP,   _______, RESET,
+        _______, KC_VOLD, KC_VOLU, KC_MUTE, _______, _______, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, _______, _______,
+        _______, KC_NO,	  _______, _______, _______, _______, _______, KC_PPLS, KC_PMNS, KC_END,  KC_PGDN, KC_DOWN, _______, _______, _______,
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______)
+
+};

@@ 0,0 1,20 @@
+YD60MQ
+======
+
+![YD60MQ PCB](https://ae01.alicdn.com/kf/HTB1PVQ2X_HuK1RkSndVq6xVwpXaO.jpg)
+
+Customizable 60% PCB by [YMDK](https://ymdk.aliexpress.com/store/429151?spm=2114.10010108.0.0.3ab23641lIkgzm).
+
+Keyboard Maintainer: QMK Community  
+Hardware Supported: YD60MQ  
+Hardware Availability: YMDK - [AliExpress](https://www.aliexpress.com/item/YMDK-60-YD60MQ-QMK-Programmable-Underglow-RGB-Led-PCB-Plate-Stabilizers-For-DIY-Mechanical-Keyboard-Interchange/32869207240.html)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make yd60mq:default
+
+The keyboard uses a DFU bootloader. To make a keymap and use dfu-util to flash it:
+
+    make yd60mq:default:dfu
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.

@@ 0,0 1,61 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = no	# Console for debug(+400)
+COMMAND_ENABLE = no    # Commands for debug and configuration
+SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = yes

@@ 0,0 1,13 @@
+#include "yd60mq.h"
+
+void led_set_kb(uint8_t usb_led) {
+    if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+        setPinOutput(F4);
+        writePinLow(F4);
+    } else {
+        setPinInput(F4);
+        writePinLow(F4);
+	}
+
+    led_set_user(usb_led);
+}

@@ 0,0 1,18 @@
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213,       \
+	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, \
+	K400, K401, K402, K403,                   K407, K408, K409, K410, K411, K412, K413  \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 }, \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212,  K213,  KC_NO }, \
+	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  K314 }, \
+	{ K400,  K401,  K402,  K403,  KC_NO, KC_NO, KC_NO, K407,  K408,  K409,  K410,  K411,  K412,  K413,  KC_NO }  \
+}
+