A keyboards/comet46/comet46.c => keyboards/comet46/comet46.c +30 -0
@@ 0,0 1,30 @@
+#include "comet46.h"
+
+void uart_init(void) {
+ SERIAL_UART_INIT();
+}
+
+void led_init(void) {
+ DDRD |= (1<<1);
+ PORTD |= (1<<1);
+ DDRF |= (1<<4) | (1<<5);
+ PORTF |= (1<<4) | (1<<5);
+}
+
+void matrix_init_kb(void) {
+ // put your keyboard start-up code here
+ // runs once when the firmware starts up
+ matrix_init_user();
+ uart_init();
+ led_init();
+}
+
+void matrix_scan_kb(void) {
+ // put your looping keyboard code here
+ // runs every cycle (a lot)
+ matrix_scan_user();
+}
+
+void led_set_kb(uint8_t usb_led) {
+
+}
A keyboards/comet46/comet46.h => keyboards/comet46/comet46.h +79 -0
@@ 0,0 1,79 @@
+#ifndef COMET46_H
+#define COMET46_H
+
+#include "quantum.h"
+#include "matrix.h"
+#include "backlight.h"
+#include <stddef.h>
+
+#define red_led_off PORTF |= (1<<5)
+#define red_led_on PORTF &= ~(1<<5)
+#define blu_led_off PORTF |= (1<<4)
+#define blu_led_on PORTF &= ~(1<<4)
+#define grn_led_off PORTD |= (1<<1)
+#define grn_led_on PORTD &= ~(1<<1)
+
+#define set_led_off red_led_off; grn_led_off; blu_led_off
+#define set_led_red red_led_on; grn_led_off; blu_led_off
+#define set_led_blue red_led_off; grn_led_off; blu_led_on
+#define set_led_green red_led_off; grn_led_on; blu_led_off
+#define set_led_yellow red_led_on; grn_led_on; blu_led_off
+#define set_led_magenta red_led_on; grn_led_off; blu_led_on
+#define set_led_cyan red_led_off; grn_led_on; blu_led_on
+#define set_led_white red_led_on; grn_led_on; blu_led_on
+
+/*
+#define LED_B 5
+#define LED_R 6
+#define LED_G 7
+
+#define all_leds_off PORTF &= ~(1<<LED_B) & ~(1<<LED_R) & ~(1<<LED_G)
+
+#define red_led_on PORTF |= (1<<LED_R)
+#define red_led_off PORTF &= ~(1<<LED_R)
+#define grn_led_on PORTF |= (1<<LED_G)
+#define grn_led_off PORTF &= ~(1<<LED_G)
+#define blu_led_on PORTF |= (1<<LED_B)
+#define blu_led_off PORTF &= ~(1<<LED_B)
+
+#define set_led_off PORTF &= ~(1<<LED_B) & ~(1<<LED_R) & ~(1<<LED_G)
+#define set_led_red PORTF = PORTF & ~(1<<LED_B) & ~(1<<LED_G) | (1<<LED_R)
+#define set_led_blue PORTF = PORTF & ~(1<<LED_G) & ~(1<<LED_R) | (1<<LED_B)
+#define set_led_green PORTF = PORTF & ~(1<<LED_B) & ~(1<<LED_R) | (1<<LED_G)
+#define set_led_yellow PORTF = PORTF & ~(1<<LED_B) | (1<<LED_R) | (1<<LED_G)
+#define set_led_magenta PORTF = PORTF & ~(1<<LED_G) | (1<<LED_R) | (1<<LED_B)
+#define set_led_cyan PORTF = PORTF & ~(1<<LED_R) | (1<<LED_B) | (1<<LED_G)
+#define set_led_white PORTF |= (1<<LED_B) | (1<<LED_R) | (1<<LED_G)
+*/
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguements
+// The second converts the arguments into a two-dimensional array
+#define LAYOUT_kc( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k10, k11,\
+ k12, k13, k14, k15, k16, k17, k18, k19, k20, k21, k22, k23, k24, k25,\
+ k26, k27, k28, k29, k31, k32, k33, k34, k35, k36, k37, k38, k41, k42,\
+ k43, k44, k45, k46, k47, k48 \
+) \
+{ \
+ { KC_##k13, KC_##k01, KC_##k26, KC_##k12, KC_##k00, KC_##k11, KC_##k25, KC_##k42, KC_##k10, KC_##k24}, \
+ { KC_##k03, KC_##k28, KC_##k14, KC_##k02, KC_##k27, KC_##k41, KC_##k09, KC_##k23, KC_##k38, KC_##k08}, \
+ { KC_##k31, KC_##k16, KC_##k04, KC_##k29, KC_##k15, KC_##k22, KC_##k37, KC_##k07, KC_##k21, KC_##k36}, \
+ { KC_NO, KC_##k32, KC_##k17, KC_##k05, KC_##k43, KC_##k48, KC_##k06, KC_##k20, KC_##k35, KC_NO }, \
+ { KC_NO, KC_##k45, KC_##k33, KC_##k18, KC_##k44, KC_##k47, KC_##k19, KC_##k34, KC_##k46, KC_NO }, \
+}
+
+#define LAYOUT( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k10, k11,\
+ k12, k13, k14, k15, k16, k17, k18, k19, k20, k21, k22, k23, k24, k25,\
+ k26, k27, k28, k29, k31, k32, k33, k34, k35, k36, k37, k38, k41, k42,\
+ k43, k44, k45, k46, k47, k48 \
+) \
+{ \
+ { k13, k01, k26, k12, k00, k11, k25, k42, k10, k24}, \
+ { k03, k28, k14, k02, k27, k41, k09, k23, k38, k08}, \
+ { k31, k16, k04, k29, k15, k22, k37, k07, k21, k36}, \
+ { KC_NO, k32, k17, k05, k43, k48, k06, k20, k35, KC_NO }, \
+ { KC_NO, k45, k33, k18, k44, k47, k19, k34, k46, KC_NO }, \
+}
+#endif
A keyboards/comet46/config.h => keyboards/comet46/config.h +87 -0
@@ 0,0 1,87 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6060
+#define DEVICE_VER 0x0001
+#define MANUFACTURER SatT
+#define PRODUCT Comet46
+#define DESCRIPTION qmk keyboard firmware for Comet46
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 10
+
+/* define if matrix has ghost */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+//#define BACKLIGHT_LEVELS 3
+
+#define ONESHOT_TIMEOUT 500
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+#define PREVENT_STUCK_MODIFIERS
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+//UART settings for communication with the RF microcontroller
+#define SERIAL_UART_BAUD 1000000
+#define SERIAL_UART_DATA UDR1
+#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1)
+#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1))
+#define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1))
+#define SERIAL_UART_INIT() do { \
+ /* baud rate */ \
+ UBRR1L = SERIAL_UART_UBRR; \
+ /* baud rate */ \
+ UBRR1H = SERIAL_UART_UBRR >> 8; \
+ /* enable TX and RX */ \
+ UCSR1B = _BV(TXEN1) | _BV(RXEN1); \
+ /* 8-bit data */ \
+ UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \
+ } while(0)
+
+#endif
A keyboards/comet46/keymaps/default/keymap.c => keyboards/comet46/keymaps/default/keymap.c +103 -0
@@ 0,0 1,103 @@
+// this is the style you want to emulate.
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+
+#include QMK_KEYBOARD_H
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+enum comet46_layers
+{
+ _QWERTY,
+ _LOWER,
+ _RAISE,
+};
+
+enum custom_keycodes {
+ QWERTY = SAFE_RANGE,
+ LOWER,
+ RAISE,
+};
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+#define LOWER MO(_LOWER)
+#define RAISE MO(_RAISE)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ /* Qwerty
+ * ,-----------------------------------------+ +-----------------------------------------.
+ * | Tab | Q | W | E | R | T | | Y | U | I | O | P | Bksp |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+------+------|
+ * | Ctl | A | S | D | F | G | Esc | | Del | H | J | K | L | ; | " |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+------+------|
+ * | Shift| Z | X | C | V | B | { | | } | N | M | , | . | / | Shift|
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+-------------|
+ * | GUI | Lower| Space| | Enter| Raise| Alt |
+ * +--------------------/ \--------------------+
+ */
+ [_QWERTY] = LAYOUT(
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC,
+ KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_ESC, KC_DEL, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT,
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_LCBR, KC_RCBR, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT,
+ KC_LGUI, LOWER, KC_SPC, KC_ENT, RAISE, KC_LALT
+ ),
+
+ /* Lower
+ * ,-----------------------------------------+ +-----------------------------------------.
+ * | | ! | @ | # | $ | % | | ^ | & | * | ( | ) | |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+------+------|
+ * | | | | | | | | | ` | \ | - | = | [ | ] | |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+------+------|
+ * | | | | | | | | | ~ | | | _ | + | { | } | |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+-------------|
+ * | | | | | | | |
+ * +--------------------/ \--------------------+
+ */
+ [_LOWER] = LAYOUT(
+ _______, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______,
+ _______, _______, _______, _______, _______, _______, _______, KC_GRV, KC_BSLS, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, _______,
+ _______, _______, _______, _______, _______, _______, _______, KC_TILD, KC_PIPE, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, _______,
+ _______, _______, _______, _______, _______, _______
+ ),
+
+ /* Raise
+ * ,-----------------------------------------+ +-----------------------------------------.
+ * | | 1 | 2 | 3 | 4 | 5 | | | | | | | |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+------+------|
+ * | | F1 | F2 | F3 | F4 | F5 | F6 | | | Left | Down | Up |Right | End | |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+------+------|
+ * | | F7 | F8 | F9 | F10 | F11 | F12 | | Home | | | | | | |
+ * |------+------+------+------+------+------+------+ +------+------+------+------+------+-------------|
+ * | | | | | | | |
+ * +--------------------/ \--------------------+
+ */
+ [_RAISE] = LAYOUT(
+ _______, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, _______,
+ _______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, XXXXXXX, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_END, _______,
+ _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_HOME, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______,
+ _______, _______, _______, _______, _______, _______
+ )
+};
+
+
+void matrix_scan_user(void) {
+ uint8_t layer = biton32(layer_state);
+ switch (layer) {
+ case _QWERTY:
+ set_led_green;
+ break;
+ case _RAISE:
+ set_led_blue;
+ break;
+ case _LOWER:
+ set_led_red;
+ break;
+ default:
+ set_led_green;
+ break;
+ }
+}
A keyboards/comet46/keymaps/satt/action_pseudo_lut.c => keyboards/comet46/keymaps/satt/action_pseudo_lut.c +142 -0
@@ 0,0 1,142 @@
+#include "quantum.h"
+#include "action_pseudo_lut.h"
+
+static uint8_t send_key_shift_bit[SHIFT_BIT_SIZE];
+
+/*
+ * Pseudo layout action.
+ * This action converts a keycode in order to output the character according to the keymap you specified
+ * still your keyboard layout recognized wrongly on your OS.
+ * Memo: Using other layer keymap to get keycode
+ */
+void action_pseudo_lut(keyrecord_t *record, uint8_t base_keymap_id, const uint16_t (*keymap)[2]) {
+ uint8_t prev_shift;
+ uint16_t keycode;
+ uint16_t pseudo_keycode;
+
+ /* get keycode from keymap you specified */
+ keycode = keymap_key_to_keycode(base_keymap_id, record->event.key);
+
+ prev_shift = keyboard_report->mods & (MOD_BIT(KC_LSFT) | MOD_BIT(KC_RSFT));
+
+ if (record->event.pressed) {
+ /* when magic commands entered, keycode does not converted */
+ if (IS_COMMAND()) {
+ if (prev_shift) {
+ add_shift_bit(keycode);
+ }
+ register_code(keycode);
+ return;
+ }
+
+ if (prev_shift) {
+ pseudo_keycode = convert_keycode(keymap, keycode, true);
+ dprintf("pressed: %02X, converted: %04X\n", keycode, pseudo_keycode);
+ add_shift_bit(keycode);
+
+ if (IS_LSFT(pseudo_keycode)) {
+ register_code(QK_LSFT ^ pseudo_keycode);
+ } else {
+ /* delete shift mod temporarily */
+ del_mods(prev_shift);
+ send_keyboard_report();
+ register_code(pseudo_keycode);
+ add_mods(prev_shift);
+ send_keyboard_report();
+ }
+ } else {
+ pseudo_keycode = convert_keycode(keymap, keycode, false);
+ dprintf("pressed: %02X, converted: %04X\n", keycode, pseudo_keycode);
+
+ if (IS_LSFT(pseudo_keycode)) {
+ add_weak_mods(MOD_BIT(KC_LSFT));
+ send_keyboard_report();
+ register_code(QK_LSFT ^ pseudo_keycode);
+ /* on Windows, prevent key repeat to avoid unintended output */
+ unregister_code(QK_LSFT ^ pseudo_keycode);
+ del_weak_mods(MOD_BIT(KC_LSFT));
+ send_keyboard_report();
+ } else {
+ register_code(pseudo_keycode);
+ }
+ }
+ } else {
+ if (get_shift_bit(keycode)) {
+ del_shift_bit(keycode);
+ pseudo_keycode = convert_keycode(keymap, keycode, true);
+ } else {
+ pseudo_keycode = convert_keycode(keymap, keycode, false);
+ }
+ dprintf("released: %02X, converted: %04X\n", keycode, pseudo_keycode);
+
+ if (IS_LSFT(pseudo_keycode)) {
+ unregister_code(QK_LSFT ^ pseudo_keycode);
+ } else {
+ unregister_code(pseudo_keycode);
+ }
+ }
+}
+
+uint16_t convert_keycode(const uint16_t (*keymap)[2], uint16_t keycode, bool shift_modded)
+{
+ uint16_t pseudo_keycode;
+
+ switch (keycode) {
+ case KC_A ... KC_CAPSLOCK:
+#if defined(__AVR__)
+ if (shift_modded) {
+ pseudo_keycode = pgm_read_word(&keymap[keycode][1]);
+ } else {
+ pseudo_keycode = pgm_read_word(&keymap[keycode][0]);
+ }
+#else
+ if (shift_modded) {
+ pseudo_keycode = keymap[keycode][1];
+ } else {
+ pseudo_keycode = keymap[keycode][0];
+ }
+#endif
+ /* if undefined, use got keycode as it is */
+ if (pseudo_keycode == 0x00) {
+ if (shift_modded) {
+ pseudo_keycode = S(keycode);
+ } else {
+ pseudo_keycode = keycode;
+ }
+ }
+ break;
+ default:
+ if (shift_modded) {
+ pseudo_keycode = S(keycode);
+ } else {
+ pseudo_keycode = keycode;
+ }
+ break;
+ }
+ return pseudo_keycode;
+}
+
+uint8_t get_shift_bit(uint16_t keycode) {
+ if ((keycode >> 3) < SHIFT_BIT_SIZE) {
+ return send_key_shift_bit[keycode >> 3] & (1 << (keycode & 7));
+ } else {
+ dprintf("get_shift_bit: Can't get shift bit. keycode: %02X\n", keycode);
+ return 0;
+ }
+}
+
+void add_shift_bit(uint16_t keycode) {
+ if ((keycode >> 3) < SHIFT_BIT_SIZE) {
+ send_key_shift_bit[keycode >> 3] |= (1 << (keycode & 7));
+ } else {
+ dprintf("add_shift_bit: Can't add shift bit. keycode: %02X\n", keycode);
+ }
+}
+
+void del_shift_bit(uint16_t keycode) {
+ if ((keycode >> 3) < SHIFT_BIT_SIZE) {
+ send_key_shift_bit[keycode >> 3] &= ~(1 << (keycode & 7));
+ } else {
+ dprintf("del_shift_bit: Can't delete shift bit. keycode: %02X\n", keycode);
+ }
+}
A keyboards/comet46/keymaps/satt/action_pseudo_lut.h => keyboards/comet46/keymaps/satt/action_pseudo_lut.h +15 -0
@@ 0,0 1,15 @@
+#ifndef ACTION_PSEUDO_LUT_H
+#define ACTION_PSEUDO_LUT_H
+
+#define SHIFT_BIT_SIZE (0xE7 / 8 + 1) // 1bit per 1key
+
+#define IS_LSFT(kc) ((QK_LSFT & (kc)) == QK_LSFT)
+
+void action_pseudo_lut(keyrecord_t *, uint8_t, const uint16_t (*)[2]);
+uint16_t convert_keycode(const uint16_t (*)[2], uint16_t, bool);
+
+uint8_t get_shift_bit(uint16_t);
+void add_shift_bit(uint16_t);
+void del_shift_bit(uint16_t);
+
+#endif
A keyboards/comet46/keymaps/satt/keymap.c => keyboards/comet46/keymaps/satt/keymap.c +220 -0
@@ 0,0 1,220 @@
+// this is the style you want to emulate.
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+
+#include QMK_KEYBOARD_H
+#include "keymap_jis2us.h"
+#include "action_pseudo_lut.h"
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+enum comet46_layers {
+ _QWERTY,
+ _LOWER,
+ _RAISE,
+ _PSEUDO_US,
+ _PSEUDO_US_LOWER,
+ _PSEUDO_US_RAISE,
+ _ADJUST
+};
+
+enum custom_keycodes {
+ QWERTY = SAFE_RANGE,
+ PSEUDO_US,
+};
+
+#define KC_LWR MO(_LOWER)
+#define KC_RSE MO(_RAISE)
+#define KC_P_LW MO(_PSEUDO_US_LOWER)
+#define KC_P_RS MO(_PSEUDO_US_RAISE)
+#define KC_QWRT QWERTY
+#define KC_P_US PSEUDO_US
+#define KC_SPCT CTL_T(KC_SPC)
+#define KC_ENSF SFT_T(KC_ENT)
+#define KC_SFTA SFT_T(KC_A)
+#define KC_CTSF S(KC_LCTL)
+#define KC_IMON ALT_T(KC_F13)
+#define KC_IMOF GUI_T(KC_F14)
+#define KC_SRO S(KC_RO)
+#define KC_SYEN S(KC_JYEN)
+#define KC_CAD LCA(KC_DEL)
+#define KC_RST RESET
+
+#define LONGPRESS_DELAY 150
+
+// Fillers to make layering more clear
+#define KC_ KC_TRNS
+#define KC_XXXX KC_NO
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ [_QWERTY] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ ESC , Q , W , E , R , T , Y , U , I , O , P ,DEL ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ TAB ,SFTA, S , D , F , G ,LPRN, RPRN, H , J , K , L ,SCLN,BSPC,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ CTSF, Z , X , C , V , B ,LBRC, RBRC, N , M ,COMM,DOT ,SLSH,QUOT,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ IMOF,LWR ,SPCT, ENSF,RSE ,IMON
+ // +----+----+---/ \---+----+----+
+ ),
+
+ [_LOWER] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ ,EXLM, AT ,HASH,DLR ,PERC, CIRC,AMPR,ASTR,LPRN,RPRN, ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ , F1 , F2 , F3 , F4 , F5 , F6 , GRV ,BSLS,MINS,EQL ,LBRC,RBRC, ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , F7 , F8 , F9 , F10, F11, F12, TILD,PIPE,UNDS,PLUS,LCBR,RCBR, ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , ,
+ // +----+----+---/ \---+----+----+
+ ),
+
+ [_RAISE] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ , 1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 0 , ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ , , , , , , , XXXX,LEFT,DOWN, UP ,RGHT,END , ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , , , , HOME,XXXX,XXXX,XXXX,XXXX,XXXX, ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , ,
+ // +----+----+---/ \---+----+----+
+ ),
+
+ [_PSEUDO_US] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ ESC , Q , W , E , R , T , Y , U , I , O , P ,DEL ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ TAB ,SFTA, S , D , F , G ,ASTR, LPRN, H , J , K , L ,FN0 ,BSPC,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ CTSF, Z , X , C , V , B ,FN0 , FN0 , N , M ,COMM,DOT ,SLSH,FN0 ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ IMOF,P_LW,SPCT, ENSF,P_RS,IMON
+ // +----+----+---/ \---+----+----+
+ ),
+
+
+ [_PSEUDO_US_LOWER] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ ,EXLM,LBRC,HASH,DLR ,PERC, EQL ,CIRC, DQT,ASTR,LPRN, ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ , F1 , F2 , F3 , F4 , F5 , F6 , LCBR,JYEN,MINS,UNDS,RBRC,BSLS, ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , F7 , F8 , F9 , F10, F11, F12, PLUS,SYEN,SRO ,COLN,RCBR,PIPE, ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , ,
+ // +----+----+---/ \---+----+----+
+ ),
+
+ [_PSEUDO_US_RAISE] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ , 1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 0 , ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ , , , , , , GRV, XXXX,LEFT,DOWN, UP ,RGHT,END , ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , , , , HOME,XXXX,XXXX,XXXX,XXXX,XXXX, ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , ,
+ // +----+----+---/ \---+----+----+
+ ),
+
+ [_ADJUST] = LAYOUT_kc(
+ //,----+----+----+----+----+----+ +----+----+----+----+----+----.
+ , , , , , , , , , , , ,
+ //|----+----+----+----+----+----+----+ +----+----+----+----+----+----+----|
+ , , , , , ,CAD , QWRT, , , , , , ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , , ,RST , P_US, , , , , , ,
+ //|----+----+----+----+----+----+----| |----+----+----+----+----+----+----|
+ , , , , ,
+ // +----+----+---/ \---+----+----+
+ )
+
+};
+
+
+/*
+ * user defined action function
+ */
+enum function_id {
+ PSEUDO_US_FUNCTION,
+};
+
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
+ switch (id)
+ {
+ case PSEUDO_US_FUNCTION:
+ action_pseudo_lut(record, _QWERTY, keymap_jis2us);
+ break;
+ }
+}
+
+/*
+ * Fn action definition
+ */
+const uint16_t PROGMEM fn_actions[] = {
+ [0] = ACTION_FUNCTION(PSEUDO_US_FUNCTION),
+};
+
+void matrix_scan_user(void) {
+ uint8_t layer = biton32(layer_state);
+ switch (layer) {
+ case _LOWER:
+ set_led_red;
+ break;
+ case _RAISE:
+ set_led_blue;
+ break;
+ case _PSEUDO_US_LOWER:
+ set_led_yellow;
+ break;
+ case _PSEUDO_US_RAISE:
+ set_led_cyan;
+ break;
+ case _ADJUST:
+ set_led_magenta;
+ break;
+ default:
+ set_led_green;
+ break;
+ }
+};
+
+uint32_t layer_state_set_user(uint32_t state) {
+ switch (biton32(state)) {
+ case _PSEUDO_US:
+ return update_tri_layer_state(state, _PSEUDO_US_RAISE, _PSEUDO_US_LOWER, _ADJUST);
+ break;
+ case _PSEUDO_US_LOWER:
+ return update_tri_layer_state(state, _PSEUDO_US_RAISE, _PSEUDO_US_LOWER, _ADJUST);
+ break;
+ case _PSEUDO_US_RAISE:
+ return update_tri_layer_state(state, _PSEUDO_US_RAISE, _PSEUDO_US_LOWER, _ADJUST);
+ break;
+ default:
+ return update_tri_layer_state(state, _RAISE, _LOWER, _ADJUST);
+ break;
+ }
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ case QWERTY:
+ if (record->event.pressed) {
+ set_single_persistent_default_layer(_QWERTY);
+ }
+ return false;
+ break;
+ case PSEUDO_US:
+ if (record->event.pressed) {
+ set_single_persistent_default_layer(_PSEUDO_US);
+ }
+ return false;
+ break;
+ }
+ return true;
+}
A keyboards/comet46/keymaps/satt/keymap_jis2us.h => keyboards/comet46/keymaps/satt/keymap_jis2us.h +32 -0
@@ 0,0 1,32 @@
+#ifndef KEYMAP_JIS2US_H
+#define KEYMAP_JIS2US_H
+
+/* keymap for convert from JIS to US */
+const uint16_t PROGMEM keymap_jis2us[][2] = {
+ [KC_A ... KC_CAPS] = { 0x00, 0x00 }, /* default value */
+
+ [KC_1] = { KC_1, KC_EXLM }, /* 1 and ! -> 1 and ! */
+ [KC_2] = { KC_2, KC_LBRC }, /* 2 and " -> 2 and @ */
+ [KC_3] = { KC_3, KC_HASH }, /* 3 and # -> 3 and # */
+ [KC_4] = { KC_4, KC_DLR }, /* 4 and $ -> 4 and $ */
+ [KC_5] = { KC_5, KC_PERC }, /* 5 and % -> 5 and % */
+ [KC_6] = { KC_6, KC_EQL }, /* 6 and & -> 6 and ^ */
+ [KC_7] = { KC_7, KC_CIRC }, /* 7 and ' -> 7 and & */
+ [KC_8] = { KC_8, KC_DQT }, /* 8 and ( -> 8 and * */
+ [KC_9] = { KC_9, KC_ASTR }, /* 9 and ) -> 9 and ( */
+ [KC_0] = { KC_0, KC_LPRN }, /* 0 and (no assign) -> 0 and ) */
+ [KC_MINS] = { KC_MINS, S(KC_RO) }, /* - and = -> - and _ */
+ [KC_EQL] = { KC_UNDS, KC_COLN }, /* ^ and ~ -> = and + */
+ [KC_LBRC] = { KC_RBRC, KC_RCBR }, /* @ and ` -> [ and { */
+ [KC_RBRC] = { KC_BSLS, KC_PIPE }, /* [ and { -> ] and } */
+ [KC_BSLS] = { KC_JYEN, S(KC_JYEN) }, /* ] and } -> / and | */
+ [KC_NUHS] = { KC_NUHS, S(KC_NUHS) }, /* (no assign) */
+ [KC_SCLN] = { KC_SCLN, KC_QUOT }, /* ; and + -> ; and : */
+ [KC_QUOT] = { KC_AMPR, KC_AT }, /* : and * -> ' and " */
+ [KC_GRV] = { KC_LCBR, KC_PLUS }, /* (no assign) -> ` and ~ */
+ [KC_COMM] = { KC_COMM, KC_LT }, /* , and < -> , and < */
+ [KC_DOT] = { KC_DOT, KC_GT }, /* . and > -> . and > */
+ [KC_SLSH] = { KC_SLSH, KC_QUES }, /* / and ? -> / and ? */
+};
+
+#endif
A keyboards/comet46/keymaps/satt/readme.md => keyboards/comet46/keymaps/satt/readme.md +6 -0
@@ 0,0 1,6 @@
+## Pseudo US Layout
+
+On a Japanese Windows environment, ANSI keyboards may be recognized wrongly as a JIS keyboard.
+By using this code, you can use your ANSI keyboard under a JIS keyboard environment without changing the settings and registry of your environment.
+
+Original code by [Shela](https://github.com/qmk/qmk_firmware/tree/master/keyboards/hhkb/keymaps/shela)
A keyboards/comet46/keymaps/satt/rules.mk => keyboards/comet46/keymaps/satt/rules.mk +26 -0
@@ 0,0 1,26 @@
+SRC += action_pseudo_lut.c
+
+# Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no # Mouse keys(+4700)
+EXTRAKEY_ENABLE = no # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI controls
+AUDIO_ENABLE = no # Audio output on port C6
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+ONEHAND_ENABLE = no # Enable one-hand typing
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+ include ../../../../Makefile
+endif
A keyboards/comet46/matrix.c => keyboards/comet46/matrix.c +154 -0
@@ 0,0 1,154 @@
+/*
+Copyright 2012 Jun Wako
+Copyright 2014 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include <stdint.h>
+#include <stdbool.h>
+#if defined(__AVR__)
+#include <avr/io.h>
+#endif
+#include "wait.h"
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+#include "matrix.h"
+#include "timer.h"
+
+#if (MATRIX_COLS <= 8)
+# define print_matrix_header() print("\nr/c 01234567\n")
+# define print_matrix_row(row) print_bin_reverse8(matrix_get_row(row))
+# define matrix_bitpop(i) bitpop(matrix[i])
+# define ROW_SHIFTER ((uint8_t)1)
+#elif (MATRIX_COLS <= 16)
+# define print_matrix_header() print("\nr/c 0123456789ABCDEF\n")
+# define print_matrix_row(row) print_bin_reverse16(matrix_get_row(row))
+# define matrix_bitpop(i) bitpop16(matrix[i])
+# define ROW_SHIFTER ((uint16_t)1)
+#elif (MATRIX_COLS <= 32)
+# define print_matrix_header() print("\nr/c 0123456789ABCDEF0123456789ABCDEF\n")
+# define print_matrix_row(row) print_bin_reverse32(matrix_get_row(row))
+# define matrix_bitpop(i) bitpop32(matrix[i])
+# define ROW_SHIFTER ((uint32_t)1)
+#endif
+
+/* matrix state(1:on, 0:off) */
+static matrix_row_t matrix[MATRIX_ROWS];
+
+__attribute__ ((weak))
+void matrix_init_kb(void) {
+ matrix_init_user();
+}
+
+__attribute__ ((weak))
+void matrix_scan_kb(void) {
+ matrix_scan_user();
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+inline
+uint8_t matrix_rows(void) {
+ return MATRIX_ROWS;
+}
+
+inline
+uint8_t matrix_cols(void) {
+ return MATRIX_COLS;
+}
+
+void matrix_init(void) {
+
+ matrix_init_quantum();
+}
+
+uint8_t matrix_scan(void)
+{
+ SERIAL_UART_INIT();
+
+ uint32_t timeout = 0;
+
+ //the s character requests the RF slave to send the matrix
+ SERIAL_UART_DATA = 's';
+
+ //trust the external keystates entirely, erase the last data
+ uint8_t uart_data[11] = {0};
+
+ //there are 10 bytes corresponding to 10 columns, and an end byte
+ for (uint8_t i = 0; i < 11; i++) {
+ //wait for the serial data, timeout if it's been too long
+ //this only happened in testing with a loose wire, but does no
+ //harm to leave it in here
+ while(!SERIAL_UART_RXD_PRESENT){
+ timeout++;
+ if (timeout > 10000){
+ break;
+ }
+ }
+ uart_data[i] = SERIAL_UART_DATA;
+ }
+
+ //check for the end packet, the key state bytes use the LSBs, so 0xE0
+ //will only show up here if the correct bytes were recieved
+ if (uart_data[10] == 0xE0)
+ {
+ //shifting and transferring the keystates to the QMK matrix variable
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ matrix[i] = (uint16_t) uart_data[i*2] | (uint16_t) uart_data[i*2+1] << 5;
+ }
+ }
+
+
+ matrix_scan_quantum();
+ return 1;
+}
+
+inline
+bool matrix_is_on(uint8_t row, uint8_t col)
+{
+ return (matrix[row] & ((matrix_row_t)1<col));
+}
+
+inline
+matrix_row_t matrix_get_row(uint8_t row)
+{
+ return matrix[row];
+}
+
+void matrix_print(void)
+{
+ print_matrix_header();
+
+ for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+ phex(row); print(": ");
+ print_matrix_row(row);
+ print("\n");
+ }
+}
+
+uint8_t matrix_key_count(void)
+{
+ uint8_t count = 0;
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ count += matrix_bitpop(i);
+ }
+ return count;
+}
A keyboards/comet46/readme.md => keyboards/comet46/readme.md +16 -0
@@ 0,0 1,16 @@
+# Comet46
+
+
+
+A split wireless 40% column-staggered keyboard
+
+Keyboard Maintainer: [SatT](https://github.com/satt99)
+Hardware Supported: Comet46 PCB, atmega32u4, nRF51822
+Hardware Availability: [Comet46 PCB, case, and receiver](https://github.com/satt99/comet46-hardware)
+Firmware for nordic MCUs: [SRC and precompiled](https://github.com/satt99/comet46-firmware)
+
+Make example for this keyboard (after setting up your build environment):
+
+ make comet46:default
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
A keyboards/comet46/rules.mk => keyboards/comet46/rules.mk +73 -0
@@ 0,0 1,73 @@
+
+OPT_DEFS += -DCOMET46_ORTHO_===PROMICRO
+COMET46_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+ avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+
+# # project specific files
+SRC = matrix.c
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+# This definition is optional, and if your keyboard supports multiple bootloaders of
+# different sizes, comment this out, and the correct address will be loaded
+# automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no # Mouse keys(+4700)
+EXTRAKEY_ENABLE = no # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+CUSTOM_MATRIX = yes # Remote matrix from the wireless bridge
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
+# MIDI_ENABLE = YES # MIDI controls
+UNICODE_ENABLE = YES # Unicode
+# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
+
+USB = /dev/ttyACM0